Xiaomi Watch 2 Screen Replacement
Complete guide to Xiaomi Watch 2 screen replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Screen Replacement is one of the most common repairs for Xiaomi Watch 2. This repair involves replacing the damaged display component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
🔧 Required Tools
What You'll Need
- Replacement display part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Unfasten the screws
Opening the Mi Watch will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your watch without replacing the seals.
Before starting the disassembly, turn off your watch.
Remove the four 3.2 mm-long T3 Torx screws on the back of the watch.
A T3 screwdriver has a tight fit on these screws and might require a bit more downward pressure to unfasten the screws. A T2 fits as well but poses the risk to strip the screw heads.
Step 2: Create a small gap
Insert the flat end of a spudger into the loudspeaker opening at the top edge of the rear case assembly.
Push the spudger upwards to create a small gap between the rear case assembly and the watch housing.
Step 3: Pry up the rear case
Insert your spudger into the gap and pry up the rear case assembly.
Only work with the edge of your spudger and do not insert it deeper than 3 mm.
Steady the rear case assembly with a finger to prevent it from suddenly popping open and damaging the flex cable.
Don’t try to remove the rear case assembly all the way yet. It is still connected to the motherboard with a thin flex cable.
Step 4: Open the watch assembly
Carefully swing open the rear case assembly by folding the rear case to the side with the watch buttons.
Avoid straining the flex cable during this procedure.
Step 5: Unfasten the screw
While it's possible to remove the battery without disconnecting the rear case assembly first ([link|https://www.ifixit.com/Guide/Xiaomi+Mi+Watch+2021+Battery+Replacement/145447#s295771|jump straight to step 8]), there's a substantial risk of damaging components. We highly recommend removing the rear case assembly.
Remove the 2.7 mm-long Phillips screw securing the metal bracket.
Step 6: Remove the metal bracket
Use a pair of [product|IF145-020|tweezers] to unhinge the metal bracket and remove it.
During reassembly, make sure to [link|https://guide-images.cdn.ifixit.com/igi/wwPjfnIMy3A5CGOq.full|latch the metal bracket|new_window=true].
Step 7: Disconnect the rear case assembly
Use the flat end of a spudger to pry up and disconnect the rear case assembly connector from the motherboard.
Step 8: Disconnect the battery
Use the flat end of a spudger to pry up and disconnect the battery connector.
Step 9: Pry up the battery
Take care not to puncture or bend the battery with your tool—a punctured or bent battery may leak dangerous chemicals or cause a thermal event.
Insert an opening pick underneath the left edge of the battery.
Tilt down your opening pick to pry up the battery.
Step 10: Remove the battery
Remove the battery.
Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $48-$210)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($80-$350)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Xiaomi Watch 2 instead of replacing it, you're preventing approximately 26 kg of CO₂ emissions. Manufacturing a new Xiaomi Watch 2 generates 34 kg of CO₂, while this repair only produces about 8 kg of CO₂. That's a 76% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Xiaomi Watch 2 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.