Suunto 5 Power Button Repair
Complete guide to Suunto 5 power button repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Power Button Repair is one of the most common repairs for Suunto 5. This repair involves replacing the damaged input component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement input part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Flip your bicycle upside down. We will need to spin the pedals while testing our fix, but we don’t want the bike to go anywhere.
If you’re feeling fancy, you can instead place the bicycle in a vice grip and elevate it above the ground, but this isn’t necessary.
Step 2:
Loosen the low (L) and high (H) rear derailleur adjuster 5mm Phillips head screws using your Phillips head #1 screwdriver.
The screws are 5mm in this example, but as long as you have a screwdriver head close to that, it'll work.
If the labels are missing, you can determine the low and high screws by tightening them. The low screw will shift the limits away from the wheel when tightened, and the high screw will shift them towards the wheel when tightened.
Step 3:
Shift the back wheel into 1st gear (the largest sprocket).
Loosen the low screw with your Phillips #1 screwdriver a quarter turn and spin the pedals.
Repeat until the chain slips off towards the wheel.
Step 4:
Manually place the chain back on the largest sprocket, and tighten the low screw a quarter turn.
Spin the pedals, and repeat this step until the chain stays on the sprocket.
If you have trouble putting the chain back on, you can give it some slack by pressing down on the bottom of the derailleur.
Step 5:
Shift the back wheel into the highest gear (the smallest sprocket).
Loosen the high screw with your Phillips #1 screwdriver a quarter turn and spin the pedals.
Repeat until the chain slips off away from the wheel.
Step 6:
Manually place the chain back on the smallest sprocket, and tighten the high screw a quarter turn.
Spin the pedals, and repeat this step until the chain stays on the sprocket.
Again, if you have trouble putting the chain back on, you can give it some slack by pressing down on the bottom of the derailleur.
Flip the bicycle upright again, and you can ride without the chain slipping off.
If your hands are covered with grease after completing the repair, it'll wash off with soap and water.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$84)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$140)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Suunto 5 instead of replacing it, you're preventing approximately 32 kg of CO₂ emissions. Manufacturing a new Suunto 5 generates 35 kg of CO₂, while this repair only produces about 3 kg of CO₂. That's a 91% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Suunto 5 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.