Skip to main content
🔧
HowMuchToFixAI for a Greener Future
Display
moderate

Samsung Galaxy Watch 4 Screen Replacement

Complete guide to Samsung Galaxy Watch 4 screen replacement. Cost estimates, difficulty level, time required, and environmental impact.

💰 Cost:$80 - $350
⏱️ Time:1-2 hours
🌍 CO₂ Saved:28 kg

🌍 Share Your Environmental Impact

Inspire others to repair instead of replace! Share how much CO₂ you're saving.

Share your impact:

💰 Cost Breakdown

Parts$48 - $210
Labor$32 - $140
Total Estimated Cost$80 - $350

💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.

🔧 Repair Overview

Screen Replacement is one of the most common repairs for Samsung Galaxy Watch 4. This repair involves replacing the damaged display component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.

🔧 Required Tools

🔩 Replacement Parts

What You'll Need

  • Replacement display part (OEM or aftermarket)
  • Precision screwdriver set (Phillips #000 or pentalobe)
  • Opening tools (plastic spudger, suction cup)
  • Adhesive strips or glue
  • Clean workspace with good lighting

Step-by-Step Process

Step 1: Power down your watch

Step 1 - Image 1

Before starting repairs, take your watch off the charger and power it down.

Remove the watch band.

Step 2: Unscrew the back cover

Step 2 - Image 1

Use a Tri-point Y00 screwdriver to remove the four 4.0 mm-long screws securing the back cover.

Step 3: Pry open the back cover

Step 3 - Image 1

Insert an opening tool into the seam between the back cover and the metal housing.

Twist the opening tool to create a gap.

Don't try to remove the back cover all the way yet. The sensor flex cable is still connected to the motherboard.

Step 4: Disconnect the sensor flex cable

Step 4 - Image 1

Lay the watch face down.

Carefully swing open the back cover by folding it to the opposite site of the created gap.

Use the flat end of a spudger to pry up and disconnect the sensor flex cable from the motherboard.

Remove the back cover.

Make sure the rubber gasket is undamaged. If damaged, replace it with a new one during reassembly to maintain proper water resistance.

Step 5: Disconnect the flex cables

Step 5 - Image 1

Use the pointed end of a spudger to disconnect the hall sensor-, the display-, and the crown button flex cable.

Step 6: Unscrew the motherboard

Step 6 - Image 1

Use a Phillips screwdriver to remove the 4.4 mm-long screw securing the motherboard.

Step 7: Remove the motherboard

Step 7 - Image 1
Step 7 - Image 2

Use your fingers to lift the motherboard out from the watch assembly towards the bottom of the watch.

During reassembly, make sure none of the flex cables become trapped underneath the motherbaord.

Step 8: Remove the core assembly

Step 8 - Image 1

Place the corner of the flat end of a spudger [link|https://guide-images.cdn.ifixit.com/igi/DWVpLVtrHTSFfHIb.full|in the small opening|new_window=true] of the barometric sensor, on the opposite side of the display connector.

Twist and tilt the spudger to lever the core assembly out of the metal housing.

Thread the display flex cable through the opening in the core assembly.

Remove the core assembly.

Step 9: Heat the display

Step 9 - Image 1

Step 10: Separate the display from the watch frame

Step 10 - Image 1

If your display is cracked, keep glass shards contained by applying a strip of tape over the glass.

Use your finger to steadily push the display down through the watch's metal housing to separate the display from the frame.

Remove the display.

📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.

iFixit Difficulty: Moderate | Time: NaNh NaNm

DIY vs Professional Repair

✋ DIY Repair

  • ✅ Lower cost (parts only: $48-$210)
  • ✅ Learn new skills
  • ❌ Risk of further damage
  • ❌ No warranty
  • ❌ Requires tools and time

🔧 Professional Repair

  • ✅ Expert installation
  • ✅ Warranty included
  • ✅ Faster turnaround
  • ❌ Higher cost ($80-$350)
  • ❌ Need to find reputable shop

Environmental Impact

By choosing to repair your Samsung Galaxy Watch 4 instead of replacing it, you're preventing approximately 28 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy Watch 4 generates 36 kg of CO₂, while this repair only produces about 8 kg of CO₂. That's a 78% reduction in carbon emissions!

Get a Personalized Repair Estimate

Upload a photo of your Samsung Galaxy Watch 4 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.

Related Repair Guides