Samsung Galaxy A50 Power Button Repair
Complete guide to Samsung Galaxy A50 power button repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Power Button Repair is one of the most common repairs for Samsung Galaxy A50. This repair involves replacing the damaged input component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
What You'll Need
- Replacement input part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Insert a SIM card eject tool, a SIM eject bit or a straightened paper clip '''into the hole on the SIM tray''' located at the left side of the phone.
Press firmly to eject the tray.
Remove the SIM card tray.
When reinserting the cards, make sure to properly orient them in the tray.
Step 2:
Start by switching off your phone.
Heat an [https://www.ifixit.com/Guide/iOpener+Heating/25705|new_window=true|iOpener] and apply it to the back cover to soften the adhesive.
The adhesive of the Samsung Galaxy A50 is very strong. A hair dryer, heat gun, or hot plate may also be used if you aren't able to open the device with the iOpener. Be careful not to overheat the phone—the AMOLED display and internal battery are both susceptible to heat damage.
Step 3:
Insert an opening pick at the bottom of your phone near the USB-C port.
If you can't get between the back cover and midframe with your opening pick, you can use a suction handle or [https://d3nevzfk7ii3be.cloudfront.net/igi/4MmKE22Cy2MavVZU|strong tape|new_window=true] to pull up the back cover to create a gap.
Slide the opening pick to the bottom left corner.
Step 4:
Insert a second opening pick and slide it from the bottom to the top left corner to cut the adhesive.
If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.
Leave the opening picks in place to prevent the adhesive from resealing.
Step 5:
Insert a third opening pick under the top left corner of the back cover.
Slide the opening pick along the top edge of the phone.
Leave the opening pick in the top right corner to prevent the adhesive from resealing.
Step 6:
Insert a fourth opening pick under the top right corner of the back cover.
Slide the tip of the opening pick along the side of the phone to the bottom right corner to cut the adhesive.
Leave the opening pick in the bottom right corner to prevent the adhesive from resealing.
Step 7:
Remove the back cover.
After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.
Step 8:
Remove the 13 Phillips #00 screws (4 mm length).
Step 9:
Insert an opening pick between the display and the midframe at the bottom of your phone above the USB-C port.
Slide the pick along the bottom edge to release the clips.
Step 10:
Continue sliding the pick along the left edge of the phone to release the clips.
Step 11:
Slide the opening pick along the top edge.
Step 12:
Slide your opening pick along the right edge towards the bottom right corner.
Step 13:
Make sure you free all the clips securing the midframe.
Separate the midframe from the phone.
Step 14:
Use a spudger to disconnect the battery by prying the connector straight up from its socket.
Step 15:
Use the flat end of a spudger to pry up and disconnect the interconnect and display flex cables from the motherboard.
Step 16:
Use the flat end of a spudger to pry up and disconnect the charging port and display flex cables from the daughterboard.
Step 17:
The adhesive that holds down the battery in the Samsung Galaxy A50 is extremely strong.
Apply some isopropyl alcohol under each corner of the battery and allow it to penetrate for several minutes to help weaken the adhesive.
Alternatively, apply [https://www.ifixit.com/Guide/iOpener+Heating/25705|new_window=true|a heated iOpener] to the display directly behind the battery for two minutes to help soften the adhesive. Repeat the process as necessary.
Step 18:
Try your best not to deform the battery during this process. Soft-shell lithium-ion batteries can leak dangerous chemicals, catch fire, or even explode if damaged. Do not use excessive force or pry at the battery with metal tools.
Insert a [product|IF145-101|plastic card] underneath the bottom edge of the battery and carefully slide it underneath the battery.
Continue sliding the plastic card underneath the battery to loosen the battery adhesive.
Step 19:
Remove the battery.
Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard. Replace it with a new battery.
Before installing a new battery, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Difficult | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$84)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$140)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy A50 instead of replacing it, you're preventing approximately 57 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy A50 generates 60 kg of CO₂, while this repair only produces about 3 kg of CO₂. That's a 95% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy A50 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.