Samsung Galaxy A11 Screen Replacement
Complete guide to Samsung Galaxy A11 screen replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Screen Replacement is one of the most common repairs for Samsung Galaxy A11. This repair involves replacing the damaged display component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
🔧 Required Tools
What You'll Need
- Replacement display part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Place the SIM eject tool in the hole of the sim tray.
Push until part of the SIM tray is pushed out.
Pull out the rest of the SIM tray.
Step 2:
Gently pry open the area of the back cover near the SIM tray using an iFixit opening pick.
Gently move the pick along the gap and pry open the clips holding it together.
If possible, use multiple picks to prevent the back cover from closing.
Step 3:
Using a hair dryer on low heat, heat the fingerprint sensor in increments of 30 seconds to loosen the surrounding adhesive.
Gently push the fingerprint sensor until it detaches from the back cover.
If needed, remove the button by prying it from the bottom of the device.
Step 4:
Remove the three 3 mm screws from the shield using a Phillips #000 screwdriver.
Remove the shield from the phone.
Step 5:
Using tweezers, a spudger, or your fingers, disconnect the battery press connector from the phone.
Step 6:
If needed, use a hairdryer on low heat to soften the adhesive under the battery.
Use an iFixit pry tool to dig under the battery edge.
If needed, use multiple pry tools to hold the battery in place.
Continue to cut the adhesive under the battery until you are able to pry the battery away from the phone.
Remove the battery from the phone.
Step 7:
Gently use tweezers to peel up the copper strip on the top right of the phone.
Step 8:
Remove the three black 3 mm screws from the speaker cover using a Phillips #000 screwdriver.
Remove the cover from the phone.
Step 9:
Using tweezers, carefully remove the earpiece speaker at the top of the phone.
When using metal tools, it is important to be gentle in order to not damage the device.
If needed, you can use a hair dryer to apply heat to the speaker and loosen the adhesive.
If needed, you may orient the tweezers to your liking, gripping the earpiece horizontally or vertically, while removing it.
Step 10:
Using a spudger, detach the ribbon cable connected to the fingerprint sensor.
Remove the fingerprint sensor from the device.
Step 11:
Remove the two 3 mm silver screws from the top left of the device using a Phillips #000 screwdriver.
Step 12:
Using a spudger, disconnect the two ribbon cables attached to the battery slot from the motherboard.
Disconnect the two longer ribbon cables near the bottom right corner of the motherboard.
Lift these cables up slightly to reveal a gap.
Step 13:
Using a spudger, gently pry the motherboard up using the corner revealed in the previous step.
If needed, use a metal spudger as a sturdier alternative.
If using a metal spudger, it is important to be gentle in order to not damage any components of the device.
Remove the motherboard from the device.
Step 14:
Remove the eight silver and black 3 mm screws from the speaker cover using a Phillips #000 screwdriver.
Remove the speaker cover from the device.
Step 15:
Using a spudger, disconnect the antenna heads from the daughterboard.
Disconnect the ribbon cable from the daughterboard.
Step 16:
Using tweezers, gently pry the daughterboard from the device.
When using metal tools, it is important to be gentle in order to not damage the device.
Step 17:
Using tweezers, remove the vibrator motor from the device.
If needed, you can apply heat to loosen the adhesive from the motor.
Step 18:
The display assembly is separated from all other components and can be replaced.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Difficult | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $48-$210)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($80-$350)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy A11 instead of replacing it, you're preventing approximately 52 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy A11 generates 60 kg of CO₂, while this repair only produces about 8 kg of CO₂. That's a 87% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy A11 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.