Nokia 8.3 Screen Replacement
Complete guide to Nokia 8.3 screen replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Screen Replacement is one of the most common repairs for Nokia 8.3. This repair involves replacing the damaged display component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
What You'll Need
- Replacement display part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
First, remove the SIM and SD card trays.
Step 2: Open the back cover
Try to use a thin tool like a razor blade to start to pry open the back cover.
When you opened it up just a little bit put a [product|IF145-101|plastic card] or a plastic opening tool inside the gap.
Using the plastic tool slowly make your way around the back cover. You can also use a guitar pick or similar.
Hint: the back cover is attached to the body with several plastic noses as well as a thin strip of adhesive. The cover is quite flexible and sturdy.
Step 3: Remove logic board cover
Remove the seven Torx T5 screws from the logic board cover.
Remove the logic board cover.
Lift up the battery connector from the logic board.
Step 4: Remove battery adhesive strips
At the bottom end of the battery you will see two black ends of adhesive strips showing up from underneath the battery.
Slowly pull at those adhesive strip ends to be able to lift out the battery.
Step 5: Remove logic board
Remove of connectors from the logic board:
button connector,
display connector,
second board connector and
WIFI cable connector.
Now remove the logic board by slowly wiggling it up. There are no screws used to attached it to the case. Only an adhesive strip on its back holds it in place.
Step 6: Peal up display cable
Slowly peal up the display cable starting from the connector.
Step 7: Remove the display
***Before trying to disassemble the display you need to heat it up to loosen the adhesive that holds it in place.***
Hint: There is much less glue at the sides of the display compared to the top and bottom. So start on the sides to get under the display.
Use a flat tool like a razor blade to get under the display. Slowly loosen up the sides by cutting through the heated up adhesive.
Especially after getting under the display initially with the razor blade a slightly thicker tool like a [product|IF145-101|plastic card] might be worth a try. When loosening up the top and bottom of the display you will need patience and a plastic card won't damage the plastic frame as much.
Step 8: Clean the frame
After removing the display you will need some isopropanol alcohol to clean the leftover adhesive.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $48-$210)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($80-$350)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Nokia 8.3 instead of replacing it, you're preventing approximately 48 kg of CO₂ emissions. Manufacturing a new Nokia 8.3 generates 56 kg of CO₂, while this repair only produces about 8 kg of CO₂. That's a 86% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Nokia 8.3 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.