Garmin Vivoactive 4 Power Button Repair
Complete guide to Garmin Vivoactive 4 power button repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Power Button Repair is one of the most common repairs for Garmin Vivoactive 4. This repair involves replacing the damaged input component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
What You'll Need
- Replacement input part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Flip the watch on its back to reveal the watch band connection pins.
Step 2: Remove Bands
Wedge your fingernail or the tip of a spudger underneath the watch band's small metal pin.
Push on the pin to release the strap from it's hinge.
Pull the strap away from the watch to disconnect it.
The strap will not pull away if the pin isn't fully pushed in.
Step 3:
With both straps removed, a new replacement watch band may be inserted.
Step 4:
Use a heatgun to loosen the adhesive beneath the screen, it should take a 5-10 minutes for adhesive to loosen.
Handle the watch with care to avoid burning yourself after it has been heated. Review the [guide|151116|How to Use a Heat Gun to Soften Adhesive|new_window=true] guide.
Step 5:
Wedge a thin opening tool or your iFixit Jimmy in between the seam where the screen and the watch’s housing connect.
Pry the screen off the device.
There is a cable underneath the screen that needs to be disconnected - be careful not to rip it.
Work quickly so the adhesive doesn’t cool too much.
Step 6:
Carefully disconnect both cables from the motherboard by placing the tip of your spudger under the edge of the connector, and prying the connector straight up from its socket.
Step 7:
Remove the screen.
Step 8:
Carefully peel off the ribbon tape that is holding down the motherboard.
Step 9:
Place the tip of your spudger under the edge of the connector, and pry the connector straight up from its socket to disconnect the battery from the motherboard.
Do this carefully to avoid ripping the cable.
Step 10:
Use a Phillips #00 screwdriver to remove the 3.2 mm screw on the motherboard.
Use a Phillips #00 screwdriver to remove the 4.8 mm screw on the motherboard.
Step 11:
Pull the battery cable up to dislodge the motherboard.
Gently remove the motherboard from the socket.
The motherboard may get caught under the housing due to the clips on the edge.
Step 12:
Use the pointed tip of a spudger to carefully push on each side of the battery connector to disconnect the battery from the motherboard.
Step 13:
Use a spudger to pry the battery from the case.
Be careful not to damage any surrounding components.
There is an adhesive holding the battery down. Use an [guide|11677|iOpener|new_window=true] if it is too difficult to remove the battery with the spudger alone.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$84)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$140)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Garmin Vivoactive 4 instead of replacing it, you're preventing approximately 31 kg of CO₂ emissions. Manufacturing a new Garmin Vivoactive 4 generates 34 kg of CO₂, while this repair only produces about 3 kg of CO₂. That's a 91% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Garmin Vivoactive 4 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.