Fujitsu LifeBook 2019 Screen Replacement
Complete guide to Fujitsu LifeBook 2019 screen replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Screen Replacement is one of the most common repairs for Fujitsu LifeBook 2019. This repair involves replacing the damaged display component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
🔧 Required Tools
What You'll Need
- Replacement display part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
To prevent injury, make sure the laptop is unplugged and turned off before removing the battery.
Push the two tabs in towards the laptop.
Lift the battery up and out from the frame of the laptop.
Step 2:
Use a plastic opening tool to lift the back of the hinge cover on the left and right sides of the computer.
Step 3:
Lift the hinge cover.
The hinge cover is connected to the motherboard by a ribbon cable. To prevent damage, lift hinge cover slowly.
Step 4:
Use the [product|IF145-020|tweezers] to disconnect the ribbon cable from the motherboard.
Step 5:
With the tweezers detach hinge cover cables from the motherboard.
Remove hinge cover.
Step 6:
Lift keyboard enough to show the ribbon cable.
The keyboard has a ribbon cable attached to the motherboard. Lift keyboard carefully to prevent damage.
Step 7:
Use a plastic opening tool to release the ribbon cable from the motherboard.
Step 8:
Push the secure clips outward.
The Adapter should pop up.
Step 9:
Use [product|IF145-020|tweezers] to remove the wires from the Adapter.
Step 10:
Take out the Adapter and carefully pull the wires out from the metal casing.
Step 11:
Remove the 4mm screws from the laptop with a Philips head #0
Remove the 4.5mm screws on the back of the laptop with a Philips #0
Step 12:
Use a plastic opening tool to lift up both sides of the white tab.
Step 13:
Use [product|IF145-020|tweezers] to grab onto the lever to remove the chip from the motherboard.
Step 14:
Lift the screen up vertically
Step 15:
Remove rubber tabs with hands
Use a Philips head #0 to remove the 3mm screws
Step 16:
Use the metal spudger to pry up the edge of the plastic casing up.
Remove the plastic frame from the screen.
Step 17:
Remove the 3mm screws with a Philips head #00
Step 18:
Remove the 2.5mm screws with a Philips head #0 on both sides of the laptop
Step 19:
Lift the screen from the frame
Step 20:
Remove the ribbon from the back of the screen
Step 21:
Use a pair of tweezers remove the white connector
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $48-$210)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($80-$350)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Fujitsu LifeBook 2019 instead of replacing it, you're preventing approximately 252 kg of CO₂ emissions. Manufacturing a new Fujitsu LifeBook 2019 generates 260 kg of CO₂, while this repair only produces about 8 kg of CO₂. That's a 97% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Fujitsu LifeBook 2019 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.