Framework Laptop 16 Screen Replacement
Complete guide to Framework Laptop 16 screen replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Screen Replacement is one of the most common repairs for Framework Laptop 16. This repair involves replacing the damaged display component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
🔧 Required Tools
What You'll Need
- Replacement display part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Before you begin
Unplug all cables and fully shut down your laptop.
If your repair requires a spudger, a T5 Torx, or a Phillips screwdriver, you can use the included Framework screwdriver. Whichever works best for you!
Step 2: Create a gap
The bezel is secured with [link|https://tenor.com/view/eyebrowwiggle-coyote-roadrunner-magnet-gif-5063311|magnets|new_window=true]!
Slide your fingernail under the inside edge of either bottom corner of the bezel.
Pull the bezel away from the screen to release the first few magnets.
Step 3: Remove the bezel
Lift the bezel around the perimeter of the screen until all of its magnets are released.
Remove the bezel.
Step 4: Remove the display screws
Use a T5 Torx screwdriver to remove the four 2.4 mm‑long screws securing the display.
During reassembly, support the screen frame with your other hand as you reinsert screws to prevent the laptop from accidentally tipping over.
Step 5: Disconnect the display
Grab the display and pull it straight off the screen frame to free it from its [link|https://guide-images.cdn.ifixit.com/igi/IeUDlwkLEMvOM1ap.full|alignment pegs|new_window=true].
Don't pull the display too far from the frame, as it's still attached by a cable.
Flip the front of the display down and rest it on the keyboard.
Step 6:
Use your fingers to flip up the plastic tab and access the connector underneath.
Step 7:
Use the flat end of a spudger to lift up the metal locking tab over the display connector.
Step 8: Remove the display
Grip the display cable where it meets the connector head.
Slide the connector straight out of its socket to disconnect it.
Remove the display.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $48-$210)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($80-$350)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Framework Laptop 16 instead of replacing it, you're preventing approximately 257 kg of CO₂ emissions. Manufacturing a new Framework Laptop 16 generates 265 kg of CO₂, while this repair only produces about 8 kg of CO₂. That's a 97% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Framework Laptop 16 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.