Apple Watch Series 4 Power Button Repair
Complete guide to Apple Watch Series 4 power button repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Power Button Repair is one of the most common repairs for Apple Watch Series 4. This repair involves replacing the damaged input component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement input part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Display Opening
Before starting repairs, take your watch off the charger and power it down.
If your touchscreen is broken and prevents powering off the watch, [https://www.ifixit.com/Guide/How+to+Power+Off+a+Broken+Apple+Watch/125834|use this alternate method to power it down].
Step 2: Safety Requirements
Because the gap between the screen and watch body is so thin, a sharp blade is needed to separate the two. '''Read the following warnings carefully before proceeding.'''
'''Protect your fingers''' by keeping them completely clear of the knife. If in doubt, protect your free hand with a heavy glove, such as a leather shop glove or gardening glove.
Be careful '''not to apply too much pressure,''' as this might cause the knife to slip and cut you, or damage the watch.
'''Wear [https://www.ifixit.com/Store/Tools/Safety-Glasses/IF145-125?o=3|eye protection.|new_window=true]''' The knife or glass may break, sending pieces flying.
Feel free to attach or remove the watch band as needed to provide more control as you make repairs.
Step 3:
Leave the iOpener on the watch for at least two minutes to fully heat the screen and soften the adhesive holding it to the case.
You may need to reheat the iOpener and repeat this procedure several times until the display adhesive gets loose enough.
Step 4:
Place the edge of a curved blade into the thin gap between the display and the outer case. Start at the short side of the display, closest to the digital crown.
Press firmly ''straight down'' into the gap.
Once inserted, tilt the blade to pry the display open slightly.
Do not insert the knife more than 1/16th of an inch (~2 mm) to avoid damaging the Force Touch sensor.
Step 5:
Once you've opened a small gap with the curved blade, remove the blade and insert the thinner edge of an opening tool into the gap.
Push the opening tool into the gap, using your thumb as a pivot to lift the display open a bit farther.
Don't try to fully open or detach the display yet.
Step 6:
It's likely that the Force Touch sensor will stick to the display frame instead to the watch's body. In this case, insert an opening pick under the display and carefully separate the Force Touch gasket from the display.
To preserve the Force Touch gasket, pry carefully under the edge of the display. If the Force Touch gasket splits when lifting the display, or if you separate the gasket layers, you'll also need to replace the Force Touch gasket itself.
Slide the pick around the display to separate the adhesive between the Force Touch gasket and the display.
Don't insert the opening pick deeper than 1/16th of an inch (~2 mm) to avoid damaging other components.
Step 7:
To avoid straining the display cables, don't open the display all the way yet.
Open the display at max. to an 45° angle, and use [product|IF145-020|tweezers] to peel off the adhesive between the display and the Force Touch gasket.
Thread the adhesive around and behind the display cables to get it off completely. Since the adhesive needs to be replaced anyway, you can cut it if that makes removal easier for you.
Make sure to return to this point during the reassembly of your watch and then continue with the [guide|134081|Resealing Procedure|new_window=true].
Step 8: Battery
Carefully fold the screen to the back until you get enough space to pry out the battery.
Avoid tensioning the display cables when folding the screen to the back.
Insert an opening pick between the battery and the Taptic Engine.
A regular opening pick works fine with the 44mm version of the Apple Watch Series 4. However if you own the 40mm version and don't have enough space you can [https://d3nevzfk7ii3be.cloudfront.net/igi/4juulZTqFTclpKur.full|customize your opening pick with scissors|new_window=true].
Step 9:
Slide the opening pick along the edge of the battery to loosen the adhesive.
The adhesive which holds the battery in place is soft. However, if you're struggling to pry out the battery you can place a [https://www.ifixit.com/Guide/iOpener+Heating/25705|heated iOpener|new_window=true] on the rear side of the watch to loosen the adhesive. Apply the iOpener for at least two minutes.
Use constant, steady pressure to slowly pry the battery up, separating it from the adhesive securing it to the system board.
Mind the display cables and especially the Force Touch cable which covers the battery in one corner so you don't damage them when levering the battery out.
Make sure you don't puncture or deform the battery, as it can catch fire and/or explode if damaged.
Don't try to remove the battery all the way yet. It is still connected to the watch assembly.
Step 10:
Carefully lift the battery and bring it in a 75° angle.
Use a pair of [product|IF145-020|tweezers] to peel the black sticker off the metal plate which covers the battery connector.
Step 11:
Remove the Y000 screw (1.2 mm length).
Step 12:
Use a pair of tweezers to remove the metal plate which covers the battery connector.
Step 13:
Use the pointed end of a spudger to pry up and disconnect the battery flex cable.
Step 14:
Remove the battery.
Be sure to remove the protective liner to expose the adhesive on your new battery before you set it in place.
Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard.
If you are reusing your old battery during reassembly, you can reuse the existing adhesive to secure the battery during reassembly. Alternatively, remove the old adhesive with high isopropyl alcohol and a lint free cloth and use a small piece of double-sided tape such as [https://www.ifixit.com/Store/Tools/Tesa-61395-Tape/IF317-072?o=1|Tesa 61395|new_window=true], or a dab of liquid adhesive such as [https://www.ifixit.com/Store/Tools/E6000-Adhesive-Glue/IF145-413?o=1|E6000|new_window=true].
Step 15: Display Adhesive
The following steps describe how to apply replacement adhesive in preparation for the resealing procedure.
Apply a little bit of high isopropyl alcohol (>99%) to a Q-tip or use a [https://www.ifixit.com/Store/Tools/Adhesive-Cleanup-Kit-Set-of-12/IF145-308-1|cleaning pad|new_window=true] to gently remove the leftover adhesive on top of the Force Touch gasket.
To remove the adhesive on the edge where the display cables are running, fold down the display and carefully pull it away from the frame so there's enough space for cleaning.
Step 16:
Flip the Apple Watch upside down so the display lays flat while lifting up the case.
Remove the leftover adhesive from the back of the display.
Step 17:
Use a pair of [product|IF145-020|tweezers] to carefully remove the replacement adhesive with the blue protective film from the backing paper.
Step 18:
Hold the replacement adhesive diagonally to thread it over the display.
Slightly tilt the display forward so you can align the adhesive with the frame.
Position the replacement adhesive on top of the Force Touch gasket.
Step 19:
Use the pointed end of a spudger to make final position adjustments and press the adhesive into place.
Follow [https://www.ifixit.com/Guide/Resealing+Procedure/134081|the resealing guide|new_window=true] to reseal your watch after reassembly.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Difficult | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$84)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$140)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Apple Watch Series 4 instead of replacing it, you're preventing approximately 35 kg of CO₂ emissions. Manufacturing a new Apple Watch Series 4 generates 38 kg of CO₂, while this repair only produces about 3 kg of CO₂. That's a 92% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Apple Watch Series 4 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.