Whirlpool Stackable Dryer Dryer Motor Replacement

WARNING: Live voltage tests are required for outlet and control-board diagnosis, and accidental contact can cause serious injury or death.

Wear gloves and a long-sleeve shirt when working inside the cabinet to avoid cuts from sharp sheet metal.

If you tilt the dryer to access bottom screws, stabilize it first and get help if needed.

Pull the plug out slightly so you can touch the meter probes to the outlet slots without fully unplugging the cord.

Measure between the middle and left slots, and confirm about 120 V AC.

Measure between the middle and right slots, and confirm about 120 V AC.

Measure between the left and right slots, and confirm about 240 V AC or something near it.

WARNING: Keep fingers behind the probe guards, and don’t let the probes touch each other while they’re in the outlet.

Note: The cord and outlet can look different by model, but the diagnosis is the same if you check both 120 V legs and the 240 V between them.

Fully reset the breaker by turning it off, then turning it all the way back on.

Replace the power cord or the outlet if either is damaged.

Note: You can do the same voltage tests at the dryer’s terminal block and you should get the same readings.

Note: These screws were 5/16 inch on this unit, but they can be smaller on other models.

Pull the top panel rearward, then lift it up and out.

Note: The control board layout can look different by model.

Note: Some models have a cross brace under the power board that must be removed to access the rest of the unit.

Confirm the dryer is unplugged before disconnecting any wires.

Remove the press-mount cable tie from the front bracing.

Disconnect the harness that runs from the control board to the front interface.

Rock the interface toward the front, then lift it up.

Feed the disconnected harness through the metal bulkhead so the interface can be fully removed.

Note: Remove any additional cross pieces and screws if your model has them.

Use a 1/4 inch nut driver to remove the four screws securing the bottom of the dryer front.

Note: It can look like there are only three screws, but there are four.

Remove the two large Phillips screws at the bottom of the filter housing.

Unclip the door switch wire harness.

Remove the three screws along the top of the dryer front, and remove the middle screw last.

Caution: Once the top screws are removed, the front may lurch forward.

Route the door switch harness through the bulkhead, then lift the front up and out.

Remove the top front bracing if it blocks access on your model.

Use a 1/4 inch nut driver to remove the four bracing screws, including the top corner screws and the left and right front-side screws.

Lift the bracing up and out, and release any locking tabs on each side.

Remove the three additional screws around the blower housing if you need to separate the blower assembly from the bulkhead.

Note: Some models also have a center blower housing screw.

Remove the four bulkhead screws from around the edges of the bulkhead.

Lift the bulkhead up off the support arms, then pull it forward and out.

If the drum catches on the front roller wheels, rotate or slide the drum slightly to help dislodge the bulkhead.

Locate the idler pulley behind the blower wheel area.

Pull the idler pulley to the left to relieve belt tension.

Pull the belt rearward to free it from the idler pulley, and let the pulley relax.

Move the belt up and away from the motor pulley so the drum can come out.

Note: Some cabinets have cutouts that make drum removal easier, while others can snag the belt on the cabinet edges.

Inspect the inside of the cabinet for obvious damage or irregularities.

Remove any heavy lint buildup that could restrict airflow and reduce drying performance.

Inspect the wiring to these components for any burnt wires or terminals.

Set the multimeter to ohms or resistance.

Touch the meter probes to the thermistor terminals and read the resistance.

A good thermistor should read about 11,200 ohms at 75 °F ambient temperature.

If the meter isn’t auto-ranging, set it between 2 K and 20 K or it may show OL.

Replace the thermistor if the reading is off by more than 10% to 15%.

Use a similar white thermistor as the replacement.

Set the multimeter to ohms or resistance.

Measure across the two heating element spade terminals and look for about 10 ohms.

Replace the element if the meter shows OL or a very different value.

Test for a short by probing a heating element spade while probing the heater can, and check multiple spots on the can.

Replace the element if you get any resistance value during the can-to-terminal test.

Set the multimeter to ohms or resistance and test across the thermostat terminals.

A good thermostat should read 0.00 ohms.

Replace the thermostat if the meter shows OL.

Note: Some thermostats have three wires, and that third wire is typically for a thermistor and can’t be checked this way.

Test across the thermal fuse terminals with the multimeter set to ohms or continuity.

A good thermal fuse should read 0.00 ohms or make the continuity sound.

Replace the thermal fuse if the meter shows OL.

A blown thermal fuse is commonly caused by a lint blockage, so clean lint from the dryer, the blower housing, and the vent ductwork.

Replace the thermostat along with the thermal fuse if the fuse was blown, even if the thermostat tests good.

Note: Some models use a single mounting screw, while others require swapping the entire housing or removing multiple screws from a clamshell housing.

On this style, remove the mounting screw at the front, then bend the face cover down or remove it with a hex screw.

Pull the element straight out of the housing.

Slide the replacement element back in until fully seated.

Note: A metal protrusion on the right side helps keep the element centered and can make insertion feel tight.

Thread the belt onto the motor pulley.

Press the idler pulley to the right to apply tension to the belt.

Turn the drum by hand to confirm it spins smoothly and the blower housing moves as the drum turns.

Align the bulkhead rollers with the front lip of the drum, and rotate the drum while pushing if it won’t seat easily.

Use a 1/4 inch nut driver to install the four bulkhead corner screws.

Reinstall the blower housing screws you removed, including the bottom screw at minimum.

Reconnect the moisture sensor harness.

Reinstall the top front bracing, latch its metal fingers, and install its screws.

Hang the front panel in place, and align it with any small mounting fingers on the bracing.

Install the three top screws, the four bottom screws underneath, and the two Phillips screws at the filter housing.

Reconnect the door switch harness.

Feed the interface wire through the front bracing, seat the interface in its slots, and install the two interface screws.

Reconnect the interface harness at the control board, and reinstall the press-mount cable tie.

Reinstall the top panel and its two hex screws, then plug in the dryer and test for heat.

Plug in the dryer, secure the multimeter so the drum can’t contact the meter or leads, and start the dryer on a heat setting.

Set the multimeter to AC voltage.

Probe the red wire at the terminal block and the red wire at the control board lower-right corner, and look for about 140 V AC while heating.

Probe the red and black wires on the power board, and look for under 1 V when the board is supplying voltage.

Turn the temperature down to zero, listen for the relay click, then recheck for 0 V on red-to-red and about 240 V on red-to-black at the board.

Replace the control board if these readings are far off.