Skip to main content
🔧
HowMuchToFixAI for a Greener Future
Temperature Control
moderate

Whirlpool Side-by-Side Refrigerator Oven Thermostat Replacement

Complete guide to Whirlpool Side-by-Side Refrigerator oven thermostat replacement. Cost estimates, difficulty level, time required, and environmental impact.

💰 Cost:$150 - $300
⏱️ Time:1-2 hours
🌍 CO₂ Saved:293 kg

🌍 Share Your Environmental Impact

Inspire others to repair instead of replace! Share how much CO₂ you're saving.

Share your impact:

💰 Cost Breakdown

Parts$90 - $180
Labor$60 - $120
Total Estimated Cost$150 - $300

💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.

🔧 Repair Overview

Oven Thermostat Replacement is one of the most common repairs for Whirlpool Side-by-Side Refrigerator. This repair involves replacing the damaged temperature control component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.

🔧 Required Tools

🔩 Replacement Parts

What You'll Need

  • Replacement temperature control part (OEM or aftermarket)
  • Precision screwdriver set (Phillips #000 or pentalobe)
  • Opening tools (plastic spudger, suction cup)
  • Adhesive strips or glue
  • Clean workspace with good lighting

Step-by-Step Process

Step 1:

Step 1 - Image 1
Step 1 - Image 2

Place a towel under the water filter cover door at the base grille.

Step 2:

Step 2 - Image 1
Step 2 - Image 2

Open the filter cover door.

Once the door is open, the filter will eject out.

Step 3:

Step 3 - Image 1
Step 3 - Image 2

Open the door all the way and pull the filter out straight.

The filter might be wet so let it drip out on the towel a bit to avoid flinging water across your kitchen floors.

Step 4:

Step 4 - Image 1
Step 4 - Image 2

Remove the new filter from its packaging and take the coverings off the O-rings.

Step 5:

Step 5 - Image 1
Step 5 - Image 2

Point the arrow on the filter toward the left and slide it into the filter hole.

Doing so will cause the filter cover door to automatically begin closing.

Step 6:

Step 6 - Image 1
Step 6 - Image 2

Close the filter cover door completely.

You may need to press hard to snap the filter into the right place.

Step 7:

Step 7 - Image 1
Step 7 - Image 2

Push the filter indicator switch five times to reset the filter indicator to green.

Using a sturdy container to catch the water, depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds.

Repeat until water begins to flow.

Once the water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on and 5 seconds off) until a total of 3 gallons had been dispensed.

📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.

iFixit Difficulty: Easy | Time: NaNh NaNm

DIY vs Professional Repair

✋ DIY Repair

  • ✅ Lower cost (parts only: $90-$180)
  • ✅ Learn new skills
  • ❌ Risk of further damage
  • ❌ No warranty
  • ❌ Requires tools and time

🔧 Professional Repair

  • ✅ Expert installation
  • ✅ Warranty included
  • ✅ Faster turnaround
  • ❌ Higher cost ($150-$300)
  • ❌ Need to find reputable shop

Environmental Impact

By choosing to repair your Whirlpool Side-by-Side Refrigerator instead of replacing it, you're preventing approximately 293 kg of CO₂ emissions. Manufacturing a new Whirlpool Side-by-Side Refrigerator generates 300 kg of CO₂, while this repair only produces about 7 kg of CO₂. That's a 98% reduction in carbon emissions!

Get a Personalized Repair Estimate

Upload a photo of your Whirlpool Side-by-Side Refrigerator and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.

Related Repair Guides