Samsung Galaxy Tab S9 Charging Port Repair
Complete guide to Samsung Galaxy Tab S9 charging port repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Charging Port Repair is one of the most common repairs for Samsung Galaxy Tab S9. This repair involves replacing the damaged connectivity component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires easy skill level.
What You'll Need
- Replacement connectivity part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Heating
Apply heat to the screen to loosen the adhesive. A heating pad or 3D printer heated bed is recomended, but a heat gun or hair dryer can also do the trick, just be careful not to apply excessive heat to avoid damage to the battery.
Recommended temperature: 60-80°C, about 2-5min. Increase only if necesary, DO NOT EXCEED 100°C
Step 2: Location of adhesive and display flex connector
Take note of the location where the adhesive and display flex conector is:
Adhesive location
Dsiplay flex connector
Be careful during prying, slicing too deep risks damage to the flex cable.
Camera location (for orientation)
Step 3: Pick and pry
Using a suction cup, lift the middle right side and insert a pick and/or plastic card into the gap, slowly slice left and right
Do the same from the middle top side
Again from the middle left side
Lastly, from the middle bottom side
Once again, watch out for the display flex connector
If the pick doesn't slice through, don't force it, instead continue to apply heat and try again. Try not to insert the pick too deep.
Once the display can lift free, DO NOT SEPARATE THEM JUST YET!
Step 4: Disconnecting the display connector
Once the display can lift free from the tablet, prop the tablet as shown, such that you can hold the display and shell separately, with the bottom side facing you to facilitate the connector removal.
Using a spudger or fingernail, disconnect the display and stylus digitizer connectors from the display.
Step 5: Remove residual adhesive from the shell
Once the display is separated, use a spudger to scrape off any adhesive residue from the sides of the frame.
Optional: use kapton tape or any method you prefer to cover the camera and fingerprint sensor from dust.
Use wipes and isopropyl alcohol (70% or more) to clean off any remaining adhesive.
From this point, if you'd like to replace the battery, you would need to remove the motherboard cover at the top, disconnect the flex cables crossing the battery, and follow the instructions printed on the battery removal tabs.
There are 15 silver screws and 2 black screws holding the frame down, take note where the black screws are located for reassembly.
Step 6: Prepare and testing replacement display
Grab the replacement display from its packaging, without removing the protective plastic and adhesive liner.
Connect the display flex connector to the replacement display, then turn on the tablet to test its functionality
You may use the Samsung Members app to perform the test, as I was unable to access the ServiceMode menu for some reason. Make sure both the capacitive touch and S Pen functionality works before reassembling
If you had replaced the battery, ensure the motherboard cover is put back, otherwise the tablet will not turn on.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Difficult | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $24-$72)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($40-$120)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy Tab S9 instead of replacing it, you're preventing approximately 122 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy Tab S9 generates 125 kg of CO₂, while this repair only produces about 3 kg of CO₂. That's a 98% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy Tab S9 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.