Samsung Galaxy S20 Ultra Back Glass Replacement
Complete guide to Samsung Galaxy S20 Ultra back glass replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Back Glass Replacement is one of the most common repairs for Samsung Galaxy S20 Ultra. This repair involves replacing the damaged housing component with a new or refurbished part. The process typically takes 1-3 hours and requires difficult skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement housing part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Heat the bottom edge
Unplug and power off your phone before you begin.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
Step 2: Separate the bottom edge adhesive
Apply a suction cup to the back of the phone, as close to the center of the bottom edge as possible.
If the back cover is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken cover.
Pull on the suction cup with strong, steady force to create a gap between the back cover and the frame.
Insert the point of an opening pick into the gap.
Due to tight tolerances, this may take multiple attempts of reheating with the iOpener and separating with the suction cup before you get it right.
If you are having trouble creating a gap, apply more heat to the edge and try again.
Do not apply excessive force with the pick, or you risk cracking the back cover glass.
Step 3: Slice the adhesive
Slide the pick back and forth along the bottom edge to slice through the adhesive.
Do not attempt to cut the adhesive near the corners of the phone where the glass is curved or you risk cracking the glass panel.
Leave your opening pick in the seam to prevent the adhesive from resealing.
Step 4: Heat the left edge
Apply a heated iOpener to the left edge of the back cover for two minutes.
Step 5: Separate the left edge adhesive
Apply a suction cup to the back of the phone, as close to the center of the left edge as possible.
Pull on the suction cup with strong, steady force to create a gap between the back cover and the frame.
Insert the point of an opening pick into the gap.
As the glass on this edge is curved, you won't be able to insert this pick very far. As long as the very tip of the pick is underneath the glass's edge, you will be able to proceed.
Due to tight tolerances, this may take multiple attempts.
If you are having trouble creating a gap, apply more heat to the edge and try again.
You can try also applying a few drops of high concentration (over 90%) isopropyl alcohol into the seam to help loosen the adhesive.
Do not apply excessive force with the pick, or you risk cracking the back cover glass.
Step 6:
Once the pick is underneath the glass's edge, tilt it downward and insert it further to fully separate the back cover's adhesive.
Step 7:
Slide the pick towards the bottom edge of the phone to separate the back cover's adhesive.
Leave your pick under the left edge of the glass near the bottom of the device to prevent the adhesive from resealing.
Step 8:
Insert another pick under the center of the left edge of the back cover.
Gradually slide the pick towards the top of the device to separate the back cover's adhesive.
Take care when sliding across the ridge in the frame surrounding the volume and power buttons—the cutout in the glass may make it more prone to cracking.
Leave your pick under the left edge of the glass near the top of the device to prevent the adhesive from resealing.
Step 9: Heat the right edge
Apply a heated iOpener to the right edge of the back cover for two minutes.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
Step 10: Separate the right edge adhesive
Apply a suction cup to the back of the phone, as close to the center of the right edge as possible.
Pull on the suction cup with strong, steady force to create a gap between the back cover and the frame.
Insert the point of an opening pick into the gap.
Like with the previous edge, you will need to tilt the opening pick downward to fully insert it underneath the back cover.
Step 11:
Slide the pick towards the bottom edge of the phone to separate the back cover's adhesive.
Leave your pick under the right edge of the glass near the bottom of the device to prevent the adhesive from resealing.
Step 12:
Insert another pick underneath the center of the right edge of the back cover.
Gradually slide the pick towards the top of the device to separate the back cover's adhesive.
As you do this, the bottom edge of the back cover may release the three picks located there. If this occurs, set these picks aside as the bottom edge shouldn't reseal from this point onward.
Step 13: Heat the top edge
Apply a heated iOpener to the top edge of the back cover for two minutes.
Step 14: Separate the top edge adhesive
The glass near the corners of the back cover is curved and very susceptible to cracking. Be gentle during this step to prevent damaging your back cover.
Gradually slide the pick from the right edge of the device around the top right corner.
Continue slicing along the top edge to fully separate the back cover adhesive.
If the slicing becomes difficult at any point, stop and reapply heat before continuing.
Step 15: Remove the back cover
Lift the back cover slowly. Use opening picks to slice any remaining adhesive.
Remove the back cover.
During reassembly:
This is a good point to power on your phone and test all functions before sealing it up.
Remove any adhesive chunks with a pair of [product|IF145-020|tweezers] or your fingers. Apply heat if you're having trouble separating the adhesive.
If you're using Samsung custom-cut adhesives, [guide|152862|follow this guide|new_window=true].
If you're using double-sided tape, [guide|113604|follow this guide.|new_window=true]
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $42-$108)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($70-$180)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy S20 Ultra instead of replacing it, you're preventing approximately 64 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy S20 Ultra generates 70 kg of CO₂, while this repair only produces about 6 kg of CO₂. That's a 91% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy S20 Ultra and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.