Samsung Galaxy Book 3 Charging Port Repair
Complete guide to Samsung Galaxy Book 3 charging port repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Charging Port Repair is one of the most common repairs for Samsung Galaxy Book 3. This repair involves replacing the damaged connectivity component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires easy skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement connectivity part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Access the rubber feet
Before you begin, shut down your laptop and unplug it.
Close the screen and lay your laptop down with the rear case facing up to access the four rubber feet.
Step 2: Remove the rubber feet
Insert an opening pick between the rear case and the rubber foot.
Pry up with the pick and dislodge the foot from the rear case.
Use [product|IF145-020|tweezers] or your fingers to remove the rubber foot.
Repeat this process on the remaining rubber feet.
There are two types of rubber feet for this laptop. During reassembly, make sure the [link|https://guide-images.cdn.ifixit.com/igi/L2ZoWXvLMERBIVcf.full|top feet|new_window=true] say "M4" and the [link|https://guide-images.cdn.ifixit.com/igi/2qKDgh1KEc1rBRNs.full|bottom feet|new_window=true] say "M1".
To reinstall a rubber foot, align it over the recess and push down until it's secured.
Step 3: Unfasten the rear case
Use a Phillips screwdriver to remove the four 4.5 mm screws securing the rear case.
Throughout this repair, [product|IF145-167-4|keep track of each screw|new_window=true] and make sure it goes back exactly where it came from.
Step 4: Insert an opening pick
Apply a suction handle to the middle of the rear case's bottom edge, as close to the edge as possible.
Pull up on the handle with a strong, steady force to create a small gap between the rear case and the frame.
This may take significant force and multiple tries.
Insert an opening pick into the gap you created.
Step 5: Release the clips
Slide the opening pick along the bottom edge to release the clips securing the rear case.
Continue sliding the pick along the perimeter of the laptop until all the clips securing the rear case have been released.
Step 6: Remove the rear case
Lift the rear case up and away from the laptop and remove it.
During reassembly, this is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down before you continue working.
Step 7: Remove the battery connector's tape
Use [product|IF145-020|tweezers] or your fingers to peel up and remove the tape covering the battery connector.
Set the tape aside. You'll reuse it during reassembly.
Step 8: Disconnect the battery
Insert the flat end of a spudger under the battery cables, as close to the connector as possible.
Gently pry up and disconnect the battery connector from its socket.
Step 9: Unfasten the battery
Use a Phillips screwdriver to remove the four 4.5 mm screws securing the battery.
Take care not to puncture the battery with your screwdriver—a punctured battery may leak dangerous chemicals or cause a fire.
Step 10: Remove the battery
Lift the battery straight out of its recess and remove it.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $24-$72)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($40-$120)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy Book 3 instead of replacing it, you're preventing approximately 252 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy Book 3 generates 255 kg of CO₂, while this repair only produces about 3 kg of CO₂. That's a 99% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy Book 3 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.