Samsung Galaxy Book 1 Keyboard Replacement

Before you begin, power down your laptop and unplug it.

There are [link|https://guide-images.cdn.ifixit.com/igi/lRQYnJPK1QMXOcJE.full|new_window=true|two kinds of rubber feet] along the top and bottom of the rear case. Keep track of their position as you remove them.

Insert an opening pick between the rubber foot and the rear case.

Pry up with the opening pick to release the clips securing the foot.

Remove the foot.

Repeat this procedure for the three remaining feet.

During reassembly, press the feet into their correct slot to reinsert them. Mismatched feet won't fit correctly.

Use a Phillips screwdriver to remove the four 4.5 mm-long screws securing the rear case.

Apply a suction cup to the rear case, as close to the center of the bottom edge as possible.

Pull up on the suction cup with strong, steady force to create a gap between the rear case and the frame.

Insert an opening pick into the gap.

Slide the pick along the bottom edge of the rear case to release its plastic clips.

Repeat this process for the left and right edges, but ***stop before reaching the top edge.***

The top edge of the rear case is lightly adhered to the frame.

Pull the top of the rear case away from the frame to separate the adhesive and release the remaining clips.

If you're having trouble separating the adhesive, use an [link|https://www.ifixit.com/Guide/iOpener+Heating/25705|new_window=true|iOpener], hair dryer, or [link|https://www.ifixit.com/Guide/How+to+Use+a+Heat+Gun+to+Soften+Adhesive/151116|new_window=true|heat gun] to soften it.

Remove the rear case.

During reassembly, perform the following:

If you're using a using a genuine Samsung replacement rear case, be sure to peel off any adhesive liners from the rear case before securing the top edge's clips.

If you're reusing your rear case, you can use some [link|During reassembly, %5Bhttps://www.ifixit.com/Guide/How+to+Use+a+Pre-Cut+Adhesive+Sheet/113604%7Cfollow this guide|new_window=true%5D if you are using a pre-cut adhesive card.|new_window=true|pre-cut adhesive] to re-adhere the top edge if your existing adhesive is no longer sticky.

This is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down completely before you continue working.

Insert a spudger between the frame and the bottom of the battery cable connector.

Pry up and disconnect the battery cable connector.

Use a spudger to gently pry up the locking flap on the [link|https://guide-images.cdn.ifixit.com/igi/5UnDng51LtgD5Qyj.full|new_window=true|ZIF connector for the display cable].

Disconnect the display cable by sliding it out from its socket on the motherboard.

Use the tip of a spudger to pry up and disconnect the two [link|https://guide-images.cdn.ifixit.com/igi/TJgdpa4eL4VoqFQK.full|new_window=true|WLAN antenna cables].

Pry under the bottom of the cable's metal head and not the cable itself.

During reassembly, these can be tricky to reconnect. One at a time, hold each connector in place over its socket and press down with the flat end of a spudger. The connector should snap into place.

Use a spudger to pry up and unclip the antenna cables from their clips on the daughterboard.

Use a Phillips screwdriver to remove one 4.5 mm-long screw securing each screen hinge (two screws total).

Each hinge has a second screw, which you should leave in place for now.

Fully open the screen and stand your laptop up on one side.

Use a Phillips screwdriver to remove the two remaining 4.5 mm screws (one from each hinge).

Remove the topmost screw last, using one hand to steady both halves of the laptop to make sure they don't separate and fall over unexpectedly.

Keep a firm grip on both the screen and frame of the laptop. Either half can fall unexpectedly during this step.

Push both halves of the laptop together so that the hinges can be lifted clear of their recesses in the frame.

Push the frame of the laptop away from you while pulling the screen toward you to separate it.

Remove the screen.

During reassembly, first install the hinge screws without tightening them fully. Then adjust the screen until it's correctly centered and aligned on each side. Finally, tighten the screws.