Samsung Galaxy A32 WiFi Antenna Repair
Complete guide to Samsung Galaxy A32 wifi antenna repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
WiFi Antenna Repair is one of the most common repairs for Samsung Galaxy A32. This repair involves replacing the damaged connectivity component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement connectivity part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Heat the back cover
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
Step 2: Insert an opening pick
Secure a suction handle to the bottom edge of the back cover, as close to the edge as possible.
If the back cover is cracked, the suction handle may not stick. Try [https://d3nevzfk7ii3be.cloudfront.net/igi/4MmKE22Cy2MavVZU|lifting it with strong tape|new_window=true], or superglue the suction handle in place and allow it to cure so you can proceed.
Lift the back cover with the suction handle to create a small gap between the back cover and the frame.
In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the [https://www.ifixit.com/Guide/iOpener+Heating/25705|iOpener|new_window=true] instructions to avoid overheating.
Insert an opening pick into the gap you created.
Slide the opening pick to the bottom right corner to slice the adhesive.
Leave the opening pick in place to prevent the adhesive from resealing.
Step 3: Slice the adhesive
Insert a second opening pick at the bottom edge of your phone.
Slide the opening pick to the bottom left corner to slice the adhesive.
Leave the opening picks in place to prevent the adhesive from resealing.
Step 4: Slice the adhesive
If the adhesive becomes hard to cut, it has most likely cooled down. [https://www.ifixit.com/Guide/iOpener+Heating/25705|new_window=true|Use your iOpener] for one to two minutes to reheat it.
Insert a third opening pick at the bottom left corner of your phone.
Slide the opening pick along the left edge of your phone to slice the adhesive.
Leave the opening pick in the top left corner to prevent the adhesive from resealing.
Step 5:
Insert a fourth opening pick underneath the top left corner of your phone.
Slide the opening pick along the top edge to slice the adhesive.
Leave the opening pick in the top right corner to prevent the adhesive from resealing.
Step 6:
Insert a fifth opening pick underneath the top right corner.
Slide the opening pick along the right edge of the back cover to slice the remaining adhesive.
Step 7: Remove the back cover
Remove the back cover.
Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).
Step 8: Eject the SIM card tray
Insert a SIM card eject tool, a SIM eject bit, or a straightened paper clip into the hole on the SIM tray located at the left edge of the phone.
Press directly into the hole to eject the SIM card tray.
Remove the SIM card tray.
Step 9: Unfasten the midframe screws
Use a Phillips screwdriver to remove the sixteen 4.1 mm-long screws securing the midframe.
Step 10: Disconnect the power and volume button flex cable
Use a spudger to disconnect the power and volume button flex cable by prying the connector straight up from its socket.
Step 11: Insert an opening pick
The midframe of the Samsung Galaxy A32 5G is held in place by plastic clips.
Insert an opening pick between the midframe and front panel assembly on the left edge of the phone where the SIM tray slot is located.
Step 12: Release the plastic clips
The plastic clips of the midframe are sitting in place tightly. Releasing them might require some force.
Slide the opening pick along the left edge of the phone to release the plastic clips.
Step 13:
Slide the opening pick around the bottom left corner.
Slide the opening pick along the bottom edge of the phone to release the plastic clips.
Step 14:
Slide the opening pick around the bottom right corner.
Slide the opening pick along the right edge of the phone to release the plastic clips.
Step 15:
Slide the opening pick around the top right corner.
Slide the opening pick along the top edge of the phone to release the remaining plastic clips.
Step 16: Remove the midframe
Place your phone with the display facing downwards on your working surface.
Remove the midframe.
Step 17: Disconnect the battery cable
Use a spudger to disconnect the battery cable by prying the connector straight up from its socket.
Step 18: Disconnect the display cable
Use a spudger to disconnect the display cable by prying the connector straight up from its socket.
Step 19: Disconnect the digitizer cable
Use a spudger to disconnect the digitizer cable by prying the connector straight up from its socket.
Step 20: Loosen the display adhesive
Apply a [https://www.ifixit.com/Guide/iOpener+Heating/25705|heated iOpener|new_window=true] to the screen to loosen the adhesive underneath. Apply the iOpener for at least 5 minutes.
The display adhesive of the Galaxy A32 5G is strong, and it's likely you need to reheat and reapply the iOpener several times before starting the display removal and during the removal procedure.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device.
Step 21: Create a gap
Once the screen is warm to touch, apply a suction cup to the right edge of the screen.
If your screen is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, [link|https://d3nevzfk7ii3be.cloudfront.net/igi/4MmKE22Cy2MavVZU|very strong tape|new_window=true] may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the screen.
Lift the screen with the suction handle to create a small gap between the screen and the front panel assembly.
Insert an opening pick in the gap between the front panel assembly and the screen.
Slide the opening pick to the top right corner of the screen to slice its adhesive.
Leave the opening pick in place to prevent the adhesive from resealing.
Step 22: Slice the adhesive
Insert a second opening pick in the gap between the front panel assembly and the screen.
Slide the opening pick to the bottom right corner of the screen to slice its adhesive.
Leave the opening pick in place to prevent the adhesive from resealing.
Step 23:
If the adhesive becomes hard to cut, it has most likely cooled down. [https://www.ifixit.com/Guide/iOpener+Heating/25705|new_window=true|Use your iOpener] or heat gun for 1-2 minutes to reheat it.
Insert a third opening pick underneath the bottom right corner of the screen.
Slide the opening pick to the bottom left corner of the screen to slice its adhesive.
Leave the opening pick in its place to prevent the adhesive from resealing.
Step 24:
Insert a fourth opening pick underneath the bottom left corner and slide it along the left edge of the phone to slice the adhesive.
Leave the opening pick in its place to prevent the adhesive from resealing.
Step 25:
When you slice near the front facing camera, insert only the tip of the opening pick (~2-3 mm) to avoid damaging or smearing the camera.
Insert a fifth opening pick at the top left corner of the screen.
Slide the opening pick along the top edge of the phone to slice the remaining adhesive.
Do not try to remove the display all the way yet, the screen and the digitizer cable are still threaded through the front panel assembly.
Step 26: Free the display cables
Thread the screen and the digitizer flex cables through the gap in the front panel assembly.
Step 27: Remove the screen
Remove the screen.
Apply new adhesive where it's necessary after cleaning the relevant areas with isopropyl alcohol (>90%).
During reassembly, [https://www.ifixit.com/Guide/How+to+Use+a+Pre-Cut+Adhesive+Sheet/113604|follow this guide|new_window=true] in case you're using a pre-cut adhesive card.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $36-$108)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($60-$180)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy A32 instead of replacing it, you're preventing approximately 56 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy A32 generates 60 kg of CO₂, while this repair only produces about 4 kg of CO₂. That's a 93% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy A32 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.