Samsung Galaxy A15 Back Glass Replacement
Complete guide to Samsung Galaxy A15 back glass replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Back Glass Replacement is one of the most common repairs for Samsung Galaxy A15. This repair involves replacing the damaged housing component with a new or refurbished part. The process typically takes 1-3 hours and requires difficult skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement housing part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Prepare the phone for disassembly
Let the phone's battery drain below 25% before starting this repair. A charged lithium-ion battery may catch fire if damaged.
Unplug all cables and completely power off the phone.
Press and hold the power and volume down buttons at the same time to bring up the shutdown menu.
Step 2: Heat the right edge
A [guide|157348|hair dryer|new_window=true] may also be used, but be careful not to overheat the phone—the display, internal battery, and plastic back are susceptible to heat damage. The phone should be just too hot to touch comfortably.
Step 3:
While you're waiting for the adhesive to soften, here is some useful information:
There's adhesive securing the back cover around the perimeter of the frame.
There is an additional layer of adhesive towards the bottom of the phone. Apart from this area, you should not be deeper than 4 mm from the edge.
Step 4: Insert an opening pick
Apply a suction handle to the back cover, as close to the center of the right edge as possible.
Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.
If you have trouble, apply more heat to further soften the adhesive.
Insert an opening pick into the gap.
Step 5: Slice the adhesive
Slide the opening pick along the right edge between the back cover and the frame to slice through the adhesive.
Leave the opening pick in the bottom right corner to keep the adhesive from resealing.
Step 6:
Reheat your iOpener and apply it to the bottom of the back cover for two minutes.
Step 7:
Insert another opening pick in the bottom right corner and slide it along the bottom edge to slice through the adhesive.
Leave this opening pick in the bottom left edge to prevent the adhesive from resealing.
Step 8:
Reheat your iOpener and apply it to the left side of the back cover for two minutes.
Step 9:
Insert another opening pick in the bottom left corner and slide it along the left edge to slice through the adhesive.
Leave this opening pick in the top left corner to prevent the adhesive from resealing.
Only insert the pick up to 4 mm deep to avoid damaging the rear cameras or flash.
Step 10:
Reheat your iOpener and apply it to the top of the back cover for two minutes.
Step 11:
Insert another opening pick in the top left corner at the same depth and slide it along the top edge to slice through the adhesive.
Leave this opening pick in the top right corner to prevent the adhesive from resealing.
Step 12: Unfasten the camera clips
Insert an opening pick along the top edge of the phone and twist it gently to unfasten the camera clips.
Slide the opening pick around the edge of the camera modules to unfasten the remaining camera clips.
Only insert the pick up to 4 mm to avoid damaging the rear cameras or flash.
Step 13: Slice remaining adhesive
Once the adhesive around the edges is loose, insert an opening pick deeper into the bottom edge from the bottom left corner.
Slide the pick deeper into the phone across the bottom edge, slicing the remaining adhesive.
Step 14: Remove the back cover
Lift and remove the back cover.
During reassembly:
This is a good point to power on the phone and test all functions before sealing it up. Be sure to power the phone back down completely before you continue working.
Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat and isopropyl alcohol (90% or greater) if you're having trouble removing the adhesive.
If you're using custom-cut adhesives, [guide|152862|follow this guide|new_window=true].
If you're using double-sided tape, [guide|113604|follow this guide.|new_window=true]
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $42-$108)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($70-$180)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy A15 instead of replacing it, you're preventing approximately 54 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy A15 generates 60 kg of CO₂, while this repair only produces about 6 kg of CO₂. That's a 90% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy A15 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.