Samsung Galaxy A10 Battery Replacement
Complete guide to Samsung Galaxy A10 battery replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Battery Replacement is one of the most common repairs for Samsung Galaxy A10. This repair involves replacing the damaged power component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires moderate skill level.
What You'll Need
- Replacement power part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Insert a SIM card eject tool, a SIM eject bit or a straightened paper clip into the hole on the SIM tray located at the left side of the phone.
Press firmly to eject the tray.
Step 2:
Remove the SIM card tray.
When reinserting the cards, make sure to properly orient them in the tray.
Step 3:
The back cover is held in place by plastic clips.
Insert an opening pick between the screen and the back cover on the bottom of the phone where the charging port is located.
Step 4:
Slide the opening pick to the bottom left corner to release the clips.
Step 5:
Slide the opening pick along the left edge to the top left corner of the phone, to release the clips.
Step 6:
Slide the opening pick from the top left corner to the top right corner to release the plastic clips.
Step 7:
Slide the opening pick from the top left corner to the bottom right corner to release the remaining clips.
Step 8:
Remove the back cover.
Step 9:
Remove the three Phillips #00 screws (3 mm length).
Step 10:
Use the flat end of a spudger to pry up the motherboard cover to release the plastic clips which hold the cover in its place.
The clips can be a bit resistive. If you're having trouble prying up the motherboard cover, twist the spudger to make the process easier.
Remove the motherboard cover.
The remaining plastic clips should release during this process or can be unhinged easily by hand.
Step 11:
Use a spudger to disconnect the battery by prying the connector straight up from its socket.
Step 12:
Use the flat end of a spudger to pry up and disconnect the interconnect and display flex cables from the motherboard.
Step 13:
Remove the eight Phillips #00 screws from the bottom (3 mm length).
Step 14:
Remove the daughterboard cover.
Step 15:
Use a spudger to disconnect the interconnect cable by prying the connector straight up from its socket.
Remove the interconnect cable.
Step 16:
Apply [https://www.ifixit.com/Guide/iOpener+Heating/25705|new_window=true|a heated iOpener] to the screen to loosen the adhesive beneath the battery. Apply the iOpener for at least two minutes. You might need to repeat this procedure several times during the battery replacement.
Step 17:
Carefully bend the display cable away from the battery to make room for removal.
Take care to bend the cable only slightly.
Step 18:
Try your best not to deform the battery during this process. Soft-shell lithium-ion batteries can leak dangerous chemicals, catch fire, or even explode if damaged. Do not use excessive force or pry at the battery with metal tools.
Insert a [product|IF145-101|plastic card] underneath the bottom edge of the battery.
Carefully slide it underneath the battery to loosen the adhesive.
Continue sliding the plastic card underneath to pry up the battery from the bottom.
Step 19:
Remove the battery.
Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard. Replace it with a new battery.
Secure the new battery with pre-cut adhesive or double-sided adhesive tape. In order to position it correctly, apply the new adhesive into the device at the places where the old adhesive was located, not directly onto the battery. Press the new battery firmly into place.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$120)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$200)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Samsung Galaxy A10 instead of replacing it, you're preventing approximately 55 kg of CO₂ emissions. Manufacturing a new Samsung Galaxy A10 generates 60 kg of CO₂, while this repair only produces about 5 kg of CO₂. That's a 92% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Samsung Galaxy A10 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.