OnePlus 8 Back Glass Replacement
Complete guide to OnePlus 8 back glass replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Back Glass Replacement is one of the most common repairs for OnePlus 8. This repair involves replacing the damaged housing component with a new or refurbished part. The process typically takes 1-3 hours and requires difficult skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement housing part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Heat the rear glass
Power off your phone and unplug any cables.
You can also use a [link|https://www.ifixit.com/Guide/How+to+Use+a+Hair+Dryer+to+Soften+Adhesive/157348|new_window=true|hair dryer], [link|https://www.ifixit.com/Guide/How+to+Use+a+Heat+Gun+to+Soften+Adhesive/151116|new_window=true|heat gun], or hot plate—but extreme heat can damage the display and internal battery, so proceed with care.
Step 2: Insert an opening pick
Apply a suction handle to the center of the bottom edge of the rear glass, as close to the edge as possible.
If your display is badly cracked, [https://www.ifixit.com/Guide/How+to+Tape+Over+a+Cracked+Phone+Screen/140533|cover it with a layer of clear packing tape|new_window=true] to help the suction cup adhere. Alternatively, you can pull using very strong tape instead of a suction cup. If all else fails, try supergluing the suction cup to the broken screen.
Pull up on the suction handle with strong, steady force to create a gap between the rear glass and frame.
Insert an opening pick into the gap.
Step 3: Slice the bottom edge adhesive
Slide the opening pick to the bottom right corner to slice the adhesive securing the rear glass.
Leave the opening pick in the bottom right corner to prevent the adhesive from resealing.
Step 4:
Insert a second opening pick under the bottom edge of the rear glass, into the gap you just created.
Slide the opening pick to the bottom left corner to slice the adhesive.
Leave the opening pick in the bottom left corner to prevent the adhesive from resealing.
Step 5: Slice the left edge adhesive
If you have trouble slicing, reheat the iOpener and apply it to the edge for two minutes to soften the adhesive.
Insert a third opening pick under the bottom left corner of the rear glass.
Slide the opening pick up the left edge to slice the adhesive.
Leave the opening pick in the top left corner to prevent the adhesive from resealing.
Step 6: Slice the top edge adhesive
Insert a fourth opening pick under the top left corner of the rear glass.
Slide the opening pick along the top edge to slice the adhesive.
Leave the opening pick in the top right corner to prevent the adhesive from resealing.
Step 7: Slice the right edge adhesive
Insert a fifth opening pick under the top right corner of the rear glass.
Slide the opening pick down the right edge to slice the remaining adhesive.
Step 8: Remove the rear glass
Remove the rear glass.
If the rear glass still feels stuck to the frame, slide an opening pick around the entire perimeter until the rear glass separates completely.
During reassembly:
After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $42-$108)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($70-$180)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your OnePlus 8 instead of replacing it, you're preventing approximately 55 kg of CO₂ emissions. Manufacturing a new OnePlus 8 generates 61 kg of CO₂, while this repair only produces about 6 kg of CO₂. That's a 90% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your OnePlus 8 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.