Nokia 8.3 Logic Board Repair
Complete guide to Nokia 8.3 logic board repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Logic Board Repair is one of the most common repairs for Nokia 8.3. This repair involves replacing the damaged logic component with a new or refurbished part. The process typically takes 3-6 hours and requires difficult skill level.
🔧 Required Tools
What You'll Need
- Replacement logic part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Press down on the back of the phone with your thumb. Then slide the back plate upward toward the top of the phone.
Lift the back plate off the phone.
Step 2:
To release the battery, press the two tabs that are located directly above the battery towards the top of the phone at the same time.
Step 3:
Lift the battery out of the phone.
Note: Upon reassembly of the phone refer to second picture. The bottom of the battery with three square openings should line up with the prongs sticking out of the phone.
Step 4:
Use a pry tool towards the bottom of the phone to gently detach the face plate from the dark grey phone frame.
Hold phone frame down while separating the face plate.
Separate the faceplate and grey phone frame.
Step 5:
Remove the six screws using a T6 screwdriver. (refer to second picture to help identify T6 screwdriver head).
NOTE: When reassembling the device be sure to not over tighten the screws.
Step 6:
Place the phone with the screen facing down onto a flat surface.
Place the flat edge of the pry tool into the seam on the side, just above the screen. (refer to picture on where to place pry tool).
Push the pry tool into the seam.
Pry apart the plates until the cover separates from the rest of the phone. Be careful not to apply too much pressure
Proceed to pull the front cover away from the rest of the phone. (refer to second picture for results) The marking foreshadows what we will be using in the next step.
Step 7:
Locate the charger connector. (refer to picture with marker)
Carefully lift the charger connector upward to detach.
NOTE: When reassembling this device the charger connector is placed toward the bottom of the phone. The connector has a peg sticking out that fits into the logic board. (refer to third picture)
Step 8:
Once the charger connector is pulled out, proceed with removing the logic board.
To remove the logic board, grip the four corners of the logic board and lift from the front inner case.
Notice the second picture the logic board has been turned over with the button side facing up.
Note: Upon reassembly the logic board must be placed correctly. The button side with the various circles should face down, lining up with the circular holes on the inner case.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $180-$480)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($300-$800)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Nokia 8.3 instead of replacing it, you're preventing approximately 36 kg of CO₂ emissions. Manufacturing a new Nokia 8.3 generates 56 kg of CO₂, while this repair only produces about 20 kg of CO₂. That's a 64% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Nokia 8.3 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.