Motorola Moto G Power Camera Repair
Complete guide to Motorola Moto G Power camera repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Camera Repair is one of the most common repairs for Motorola Moto G Power. This repair involves replacing the damaged optics component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires moderate skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement optics part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Position a suction cup securely on the back panel of the device.
Insert the opening pick into both sides of the phone and carefully slide it along to open the back panel of the device.
Do not fully remove the back panel; disconnect the fingerprint sensor first.
Step 2:
Apply gentle pressure to the fingerprint sensor with your finger to detach it from the back panel.
You may need to apply firm pressure to remove the circular sensor from the panel.
Step 3:
Fully remove the back panel from the device.
Step 4:
Using a Torx T3 screwdriver, remove nine 2.2 mm screws.
Step 5:
Use the spudger to gently lift the cover.
If needed, use the spudger's tip against a corner of the cover to help lift it.
Set the back cover aside.
DO NOT use excessive force when lifting up the back cover.
Step 6:
Carefully use the spudger to lift the sensor cable, disconnecting the fingerprint sensor from the motherboard.
WARNING: Handle the sensor cable with care; it can be easily damaged.
Step 7:
Carefully remove the fingerprint sensor from the device and set it aside.
Do not use excessive force when lifting the back cover or any other component.
Step 8: Protective tape
If present, carefully remove the protective tape using a plastic spudger as shown, ensuring the delicate flex cable is not torn in the process.
Be careful to not puncture or bend the battery! If punctured, it could start a fire. This is why we recommend discharging your device below 20% before beginning any repairs. Combustion could potentially cause damage to the device and your skin/clothing.
Step 9: Disconnect the flex cable
Use a plastic spudger or non-conductive [product|IF145-020|tweezers] to disconnect the battery cable from the motherboard.
Ensure the tweezers are not pointed or sharp. Be gentle to avoid tearing the flex cable. This could cause a short-circuit in the battery connector, or scratch and damage traces on the motherboard.
Step 10: Seperate the old battery from the frame
Slide an opening pick under the battery and gently work it back and forth to separate the adhesive from the battery.
This adhesive is quite strong and will require careful attention to apply the correct amount of force to remove the battery without damaging it in the process. Be patient and take it slow.
Step 11: Out with the old, in with the new
Remove the old battery and insert the replacement battery, connecting it to the motherboard.
(Optional) Two-sided tape can be used to secure the battery to the frame if the original adhesive isn't strong enough to keep the new battery in place also.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $36-$150)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($60-$250)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Motorola Moto G Power instead of replacing it, you're preventing approximately 55 kg of CO₂ emissions. Manufacturing a new Motorola Moto G Power generates 59 kg of CO₂, while this repair only produces about 4 kg of CO₂. That's a 93% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Motorola Moto G Power and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.