Motorola Moto G 5G Home Button Repair
Complete guide to Motorola Moto G 5G home button repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Home Button Repair is one of the most common repairs for Motorola Moto G 5G. This repair involves replacing the damaged input component with a new or refurbished part. The process typically takes 20-40 min and requires easy skill level.
🔧 Required Tools
What You'll Need
- Replacement input part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Eject the SIM card tray
Insert a SIM card eject tool or a straightened paperclip into the hole adjacent to the SIM card tray.
Press firmly to eject the tray.
Step 2: Remove the SIM card tray
Remove the SIM card tray from the phone.
When reinserting the SIM card, make sure it's in the proper orientation inside the tray.
Step 3: Back cover removal information
Discharge your battery to 25% or less and completely power off your phone before you begin.
Take note of the following seams along the edge of the phone:
''Screen seam'': This seam separates the display panel from the frame. ***Don't pry at this seam.***
''Bezel seam'': This is where the plastic back cover meets the rest of the phone. It's held in place by plastic clips. ***This is where you should pry.***
Step 4: Insert an opening pick
Insert an opening tool in the bezel seam halfway between the bottom-right corner of the phone and the power button.
Insert an opening pick in the gap you just created.
Step 5: Release the right clips
Slide your opening pick toward the bottom-right corner of the back cover and release the clips.
As each clip releases, you will hear and feel a pop.
Don't slide the opening pick near the power or volume buttons.
Step 6: Release the bottom clips
Continue sliding your opening pick towards the bottom left corner to unclip the bottom edge of the back cover.
Step 7: Release the left clips
Slide your opening pick toward the top left corner to unclip the left side of the back cover.
Step 8: Release the top clips
Slide your pick around the top left corner and along the top edge to release the clips.
Step 9:
Slide your pick around the top right corner to release the last clips securing the back cover.
Stop before reaching the volume buttons. Your pick may damage their cables.
Step 10: Remove the back cover
Don't try to remove the back cover all the way yet, as it's still connected to the frame by the power button cable.
With SIM card slot facing you, swing the back cover open and away from you like you're opening a book.
Rest the cover parallel to the frame.
Don't twist the screen or move it too far away from the frame to avoid damaging the power button cable.
Step 11: Remove the power button
A small rubber arm connects the power button to its recess. Use caution to avoid tearing this piece.
Use [product|IF145-020|tweezers] or your fingers to unhook the power button's rubber arm from its recess and remove it.
Step 12: Only the back cover remains
You're now left with the back cover.
This is a good point to test your phone before sealing it up. [link|https://www.ifixit.com/Guide/How+to+Test+the+Hardware+on+Your+Motorola+Phone/154941|new_window=true|Follow this guide] to perform a hardware test. Be sure to power your phone back down completely before you continue working.
Step 13: Unfasten the power button cable bracket
Use a PH00 screwdriver to remove the two 3.9 mm-long screws securing the power button cable bracket.
Step 14: Remove the power button cable bracket
Use your fingers or a pair of blunt nose [product|IF145-020|tweezers] to grab and remove the bracket from the power button cable.
Step 15: Disconnect the power button
Use the pointed end of a spudger to pry up and disconnect the power button's press connector.
Step 16: Remove the power button
Grab and remove the power button.
If you're using tweezers, take care not to puncture the battery—a punctured battery may leak dangerous chemicals or cause a fire.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $24-$60)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($40-$100)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Motorola Moto G 5G instead of replacing it, you're preventing approximately 57 kg of CO₂ emissions. Manufacturing a new Motorola Moto G 5G generates 59 kg of CO₂, while this repair only produces about 2 kg of CO₂. That's a 97% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Motorola Moto G 5G and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.