Microsoft Surface Pro 3 Battery Replacement
Complete guide to Microsoft Surface Pro 3 battery replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Battery Replacement is one of the most common repairs for Microsoft Surface Pro 3. This repair involves replacing the damaged power component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires moderate skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement power part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Before you begin, discharge the Surface Pro's battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally damaged during the repair.
The display is strongly glued to the frame of the device.
To remove the display, first soften the adhesive by applying heat. You can use a heat pad, heat gun, or iOpener. In a pinch, a hair dryer can also work.
Be careful when using a heat gun, as too much heat can permanently damage the display and/or battery.
Steadily and evenly heat the perimeter of the display until it's too hot to touch, and try to maintain that temperature for several minutes.
Step 2:
Use a suction cup or an iSclack to pull up on the glass and create a slight gap between the glass and the metal frame.
If your display is badly cracked, a suction cup may not adhere. It may help to first cover the display with a layer of packing tape. Alternatively, you can superglue your suction cup to the display.
Carefully insert an opening pick into the gap between the screen and the device to cut the adhesive.
Slide the pick around the sides and bottom of the display to cut the adhesive. Apply more heat as needed.
Work carefully—the glass is thin and will crack easily if you try to force it.
The wi-fi antennas are glued under the screen border along the top edge (on either side of the camera), and can be damaged easily. Use extra care when separating the top edge, and apply more heat if necessary.
Step 3:
Continue to heat sections of the screen with the heat gun.
As you make your way around the screen with the heat gun, use the plastic opening tool and the opening picks to pry the screen loose.
The screen is extremely thin and very easy to break. Be careful working with broken glass.
Step 4:
Lift the screen up carefully so that no wires are torn.
Step 5:
Remove the 3 mm T3 Torx screw securing the battery connector, and disconnect the battery connector.
Be careful not lose the small, rectangular bridge connector that lies underneath.
Step 6:
Remove the single 4 mm T3 Torx screw securing the display cable.
Lift the connector to disconnect the cable.
Be careful not lose the small, rectangular bridge connector that lies underneath.
Step 7:
Grasp the orange cable connected to the silver connecter.
Carefully lift the orange cable up until the connecter pops off.
The screen will now be completely disconnected.
The replacement display may not include all the parts needed for installation. Save all the parts from the original display, and transfer them to the new display as needed.
Step 8:
Use the metal spudger to scrape the battery off of the device.
There will be a fair bit of adhesive securing the battery to the device, so make sure to take your time and work the spudger around the perimeter of the battery to loosen all of the adhesive.
The Metal Spudger can potentially puncture the battery. It is safer to use the [product|IF145-101|plastic card] to remove the battery.
Step 9:
Lift the battery out of the device.
Be sure to follow instructions listed on the batteries for proper disposal.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Very difficult | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$120)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$200)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Microsoft Surface Pro 3 instead of replacing it, you're preventing approximately 255 kg of CO₂ emissions. Manufacturing a new Microsoft Surface Pro 3 generates 260 kg of CO₂, while this repair only produces about 5 kg of CO₂. That's a 98% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Microsoft Surface Pro 3 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.