Mi Band 6 Vibration Motor Repair
Complete guide to Mi Band 6 vibration motor repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Vibration Motor Repair is one of the most common repairs for Mi Band 6. This repair involves replacing the damaged haptic component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires easy skill level.
What You'll Need
- Replacement haptic part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Safety precautions
Power off the machine at least '''one hour''' prior to starting repairs. Ensure the machine is completely cool to the touch.
Flip the power switch into the '''OFF''' position.
Unplug any extension cords from the included power cord.
Step 2: Remove the upper shell
Use a 5/16 inch socket or Phillips screwdriver to remove the eight screws securing the upper shell, four on each side.
Step 3:
Lift the upper shell straight up off of the machine to remove it.
Step 4: Remove the right-side cover
Use a 5/16 inch socket or Phillips screwdriver to remove the four bolts securing the right-side cover.
Step 5:
Tilt the right-side cover down to access the PCB board.
Do not fully remove the right-side cover, it is still attached via the on/off switch.
During reassembly, ensure the display [link|https://d3nevzfk7ii3be.cloudfront.net/igi/KUo4swES5QnGQYJH.full|new_window=true|window] is aligned with the LCD display before you press the cover into place.
Step 6:
There are two wires connecting the power switch to the main PCB assembly.
Use needle nose pliers to remove the wire with the blue connector.
Remove the wire with the clear connector.
Remove the right-side cover.
During reassembly, install the power switch wires back in their original locations with the blue wire above the clear wire.
Step 7: Disconnect the ground wires
Use a 5/16 inch socket or Phillips screwdriver to remove the screw securing the two green ground wires to the frame.
Step 8: Disconnect the fuel line
Use a pair of needle nose pliers to release the hose clamp from the fuel line.
Slide the hose clamp off of the nipple, about one inch down the fuel line.
Step 9:
Pull to disconnect the fuel line from the motor and pump assembly.
Step 10:
Use a pair of needle nose pliers to remove the fuel line hose clamp.
Step 11: Disconnect the motor and pump assembly
Use a pair of needle nose pliers to disconnect the wires connecting the motor and pump assembly to the main PCB board:
One [link|https://d3nevzfk7ii3be.cloudfront.net/igi/1hRInVGfNVBTy1To.full|new_window=true|red cable] labeled '''MOTOR 2''' on the main PCB board
One [link|https://d3nevzfk7ii3be.cloudfront.net/igi/3pI1EPSb6Nahjy5U.full|new_window=true|orange cable] labeled '''MOTOR 1''' on the main PCB board
Pull the wires with the needle nose pliers by their connectors and not the wires themselves.
Step 12:
Use a pair of flush cutters to cut the cable tie harnessing the wires running from the main PCB assembly.
Remove the cable tie.
During reassembly, install a new cable tie.
Step 13:
Use a pair of flush cutters to cut the cable tie harnessing the orange, red, white, and black wires near the fuel line.
During reassembly, install a new cable tie.
Step 14:
Use a pair of flush cutters to cut the cable tie harnessing the orange and red wires next to the motor.
During reassembly, install a new cable tie.
Step 15: Detach the capacitor
Use a Phillips screwdriver to remove the screw securing the capacitor band clamp.
Step 16:
Remove the capacitor from the band clamp.
During reassembly, realign the foam padding between the capacitor and the band clamp.
Step 17: Remove the motor and pump assembly
Feed the orange and red wires out through the opening in the lower shell.
Step 18:
Use a 5/16 inch socket or Phillips screwdriver to remove the four bolts securing the left-side cover.
Step 19:
Remove the left-side cover.
Step 20:
Use a 5/16 inch socket or Phillips screwdriver to remove the four screws securing the motor mount bracket, two on each side.
Step 21:
Lift the motor, pump, and bracket assembly straight up out of the machine.
Step 22: Remove the fan
Use a 3 mm hex key to loosen the set screw securing the fan to the motor shaft.
The set screw does not need to be fully removed.
Step 23:
Remove the fan.
Step 24: Remove the motor mount bracket
Use a 5/16 inch socket or Phillips screwdriver to remove the two screws securing the motor and pump assembly to the motor mount bracket.
Step 25:
Remove the motor mount bracket.
Only the motor and pump assembly remain.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $24-$66)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($40-$110)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Mi Band 6 instead of replacing it, you're preventing approximately 26 kg of CO₂ emissions. Manufacturing a new Mi Band 6 generates 28 kg of CO₂, while this repair only produces about 2 kg of CO₂. That's a 93% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Mi Band 6 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.