MacBook Pro 14" 2014 Speaker Repair
Complete guide to MacBook Pro 14" 2014 speaker repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Speaker Repair is one of the most common repairs for MacBook Pro 14" 2014. This repair involves replacing the damaged audio component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires moderate skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement audio part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Remove the following P5 pentalobe screws securing the lower case to the MacBook Pro:
Eight 3.0 mm
Two 2.3 mm
Step 2:
Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.
Set the lower case aside.
Step 3:
Peel back the warning label covering the battery connector.
Step 4:
Using the flat end of a spudger, gently pry the battery connector straight up out of its socket on the logic board.
Bend the battery cables back and out of the way, ensuring that the battery connector doesn't accidentally make contact with the logic board.
Step 5:
Use a spudger or [product|IF145-020|tweezers] to pry the three AirPort antenna cables straight up off of their sockets on the AirPort board.
The cable connection points are fragile. Be careful to lift only on the connector, and not on the socket or cable.
To reconnect, align the connector carefully into position over the socket, and press it down firmly with the flat of your spudger.
Step 6:
Use the tip of a spudger to push the camera cable's plug toward the fan and out of its socket on the logic board.
The plug in the photo has six connections, but some models have twelve connections. The process of removing the plug from its socket is the same for both.
If the camera cable's plug won't come easily out of its socket on the logic board, fold back the rubber cover over the fan to gain access to the cable, then gently pull on the cable while using the spudger to gently push the plug out of its socket.
Be sure to push parallel to the board, first on one side, then the other, to slowly "walk" the plug out of its socket. Do not pry up, or you will damage the socket.
Step 7:
Insert the flat end of a spudger underneath the rubber heat sink cover on the right fan.
Slide the spudger underneath the length of the cover, releasing the adhesive.
Lift the cover and flip it back so that you can access the cables underneath.
Step 8:
Use your fingers to pull the AirPort/Camera cables up off the fan.
The cables are adhered to the fan, so peel them up carefully to avoid damaging them.
Carefully de-route the cables from the plastic cable guide.
Step 9:
If your I/O Board cable's connectors have [link|https://guide-images.cdn.ifixit.com/igi/NcprwYqAITaNGRVg.full|notches in the padding], you will need to '''release a locking lever underneath the notch''' in order to remove the cable. If this is the case, '''don't pry up on the connector until the levers are unlatched'''.
Using the flat end of a spudger, pry the I/O Board connector straight up out of its socket on the logic board.
During reassembly, connect this end first, as it does not flex.
In a similar fashion, remove the I/O Board cable connector from its socket on the I/O Board.
Remove the I/O Board cable from the MacBook Pro.
Step 10: Airport Card
Remove the single 2.9 mm T5 Torx screw securing the AirPort card to the logic board.
Step 11:
Grasp the sides of the AirPort card and lift it up to a shallow angle (5-10˚) to separate the light adhesive adhering it to the logic board.
Pull the AirPort card parallel out of its connector on the logic board to remove it.
Step 12:
Use the tip of a spudger to flip up the retaining flap on the right fan ribbon cable [https://www.ifixit.com/Guide/Recognizing+&+Disconnecting+Cable+Connectors/25629#s64969|ZIF|new_window=true] socket.
Be sure you are prying up on the hinged retaining flap, '''not''' the socket itself.
Starting at the top of the cable, slide a plastic opening tool under the right fan cable to free it from the logic board.
Use caution when freeing the cable, as it is strongly adhered to the logic board.
Step 13:
Remove the following three screws securing the right fan to the logic board:
One 4.4 mm T5 Torx screw
One 3.9 mm T5 Wide Head Torx screw
One 5.0 mm T5 Torx screw with 2 mm collar
Step 14:
Lift and remove the right fan out from the MacBook Pro.
When reinstalling the fan, it's easiest connect the fan ribbon cable as you drop the fan in place, rather than after you've installed the three fan screws.
Step 15:
Use the flat end of a spudger to lift the rubber heat sink cover up off the left fan.
Step 16:
Remove the following three screws securing the left fan to the logic board:
One 4.4 mm T5 Torx screw with 2 mm collar
One 5.0 mm T5 Torx screw with 2 mm collar
One 3.9 mm T5 Wide Head Torx screw
When reinstalling the fan and its screws, don't fully torque the screws until you've first installed all of them loosely, so that the fan can move a little and position itself properly as you insert the screws into their threaded standoffs.
Step 17:
Use the tip of a spudger to flip up the retaining flap on the left fan ribbon cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, '''not''' the socket itself.
Starting at the top of the cable, slide a plastic opening tool under the left fan cable to free it from the logic board.
Use caution when freeing the cable, as it is strongly adhered to the logic board. If necessary, use an iOpener or hair dryer to heat the cable in order to soften the adhesive and make it easier to remove.
Lift the left fan out of the device.
When reinstalling the fan, it's easier to connect the fan ribbon cable as you drop the fan in place, rather than after you've installed the three fan screws.
Step 18:
Remove the single 3.1 mm T5 Torx screw securing the SSD to the logic board.
Step 19:
Slightly lift the rightmost side of the SSD and firmly slide it straight away out of its socket on the logic board.
Step 20:
Use the tip of a spudger to flip up the I/O board data cable lock and rotate it toward the battery side of the computer.
Use the flat end of a spudger to slide the I/O board data cable straight out of its socket on the logic board.
Do not lift up on the I/O board data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.
Step 21:
Remove the two 3.1 mm T5 Torx screws securing the I/O board to the logic board.
On some models, also removing the silver 3.5 mm T5 Torx screw from the heatsink can aid in I/O board removal.
Carefully lift the I/O board and remove it from the lower case.
Step 22:
Use the flat end of a spudger to pry the left speaker connector up and out of its socket on the logic board.
Use the tip of a spudger to pry the right speaker connector up and out of its socket on the logic board
Be sure to pry on the cable head, and not on the socket itself. Prying on the socket may cause it to separate from the logic board.
Step 23:
Peel back the tape covering the top of the keyboard ribbon cable connector.
Use the flat end of a spudger to flip up the retaining flap on the keyboard ribbon cable [link|https://www.ifixit.com/Guide/Recognizing+&+Disconnecting+Cable+Connectors/25629|new_window=true| ZIF socket].
Be sure you are prying up on the hinged retaining flap, '''not''' the socket itself.
Use the flat end of a spudger to push the keyboard ribbon cable out of its socket.
Step 24:
Use the flat end of a spudger to pry the trackpad ribbon cable connector up out of its socket.
Step 25:
Use the flat end of a spudger to pry the keyboard backlight connector up from its socket on the logic board.
Step 26:
Use the tip of a spudger or your fingernail to flip up the retaining flap on the microphone ribbon cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, '''not''' the socket itself.
Pull the microphone ribbon cable out of its socket.
Step 27:
Use the tip of a spudger to flip up the display data cable lock and rotate it toward the DC-In side of the computer.
Pull the display data cable straight out of its socket on the logic board.
Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.
Step 28:
Use the flat end of a spudger to carefully pry off the rubber screw cap on the raised screw head near the MagSafe 2 connector.
The location of this screw may vary between models.
Step 29:
Remove the following six screws securing the logic board to to the upper case:
One 3.1 mm T5 Torx screw
One 2.5 mm T5 Torx screw
One 5.5 mm silver, raised-head T5 Torx screw
Two 5.7 mm T5 Torx screws
One 3.8 mm silver T5 Torx screw
Step 30:
Lifting from the side nearest the battery, rotate the logic board toward the top of the MacBook Pro.
You may need to slide the logic board a few millimeters to the left in order to get clearance for the ports along the right edge of the board.
Using the flat end of a spudger, carefully push the MagSafe 2 connector out of its socket on the bottom of the logic board.
Disconnecting the MagSafe 2 connector can be difficult. If you are only removing the logic board to temporarily get it out of the way, such as for a battery replacement, you may find it easier to simply [https://d3nevzfk7ii3be.cloudfront.net/igi/GOcrO3AMpJXvKgv2|remove the two 2.5 mm T5 Torx screws securing the MagSafe DC-In board|new_window=true], and then remove the logic board and MagSafe board together.
Step 31:
Remove the logic board assembly from the MacBook Pro.
While the logic board and fans are removed, use a can of compressed air and a soft, non-static brush to remove dust and other debris from the upper case and the logic board, particularly from the fan exhaust openings along the rear edge of the upper case.
When reinstalling the motherboard, make sure all cables, and the two rubber heat sink/fan covers, are visible and not trapped under the motherboard.
Second photo, clockwise from top: battery, right speaker, keyboard backlight, AirPort/camera, display, microphone, left speaker, keyboard, and trackpad.
Step 32:
Remove the following three screws securing the left speaker to the upper case:
One 5.6 mm T5 Torx screw
One 6.9 mm T5 Torx screw
One 2.6 mm T5 Torx screw
Lift the left speaker out of the upper case and set it aside.
The speaker is secured to the case with some light adhesive.
Step 33:
Remove the following three screws securing the right speaker to the upper case:
One 5.6 mm T5 Torx screw
One 6.9 mm T5 Torx screw
One 2.6 mm T5 Torx screw
Remove the right speaker from the MacBook Pro.
The speaker is secured to the case with some light adhesive.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$90)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$150)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your MacBook Pro 14" 2014 instead of replacing it, you're preventing approximately 287 kg of CO₂ emissions. Manufacturing a new MacBook Pro 14" 2014 generates 290 kg of CO₂, while this repair only produces about 3 kg of CO₂. That's a 99% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your MacBook Pro 14" 2014 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.