MacBook Air 13" 2019 Logic Board Repair
Complete guide to MacBook Air 13" 2019 logic board repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Logic Board Repair is one of the most common repairs for MacBook Air 13" 2019. This repair involves replacing the damaged logic component with a new or refurbished part. The process typically takes 3-6 hours and requires difficult skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement logic part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Remove the screws securing the lower case
Before starting this procedure, you should disable your Mac's '''Auto Boot''' feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. [https://www.ifixit.com/Guide/How+to+Disable+Auto+Boot/110034|Use this guide|new_window=true] to disable Auto Boot.
If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you're inside.
Completely power off and unplug your MacBook Air before you start. Close the display and flip the entire laptop upside-down.
Use a P5 driver to remove the following screws:
Two 7.9 mm screws
Two 7.1 mm screws
Six 2.6 mm screws
Step 2: Remove the lower case
Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Remove the lower case.
After reassembly, your MacBook might not turn on until it's connected to a power source (a low power phone charger may work). To test your repair, plug in your charger, allow two minutes for your MacBook to turn on, and check that everything works as expected.
Step 3: Disconnect the battery
Peel back the tape covering the battery connector enough to reveal the connector underneath.
Step 4:
Use a spudger to slide the battery connector parallel to the logic board and out of its socket on the logic board.
Step 5: Disconnect the logic board
Use a T3 Torx driver to remove the two 1.4 mm screws securing the trackpad connector bracket.
Depending on the condition of your bits, a T4 Torx driver may fit better.
Remove the trackpad connector bracket.
Step 6:
Use the flat end of a spudger to pry the trackpad cable connector up and out of its socket.
Step 7:
If the left speaker is already disconnected, skip this step.
Slide the tip of a spudger underneath the left speaker cable and pry straight up to disconnect the speaker.
With the connector disconnected, slide the flat end of a spudger under the cable to separate the adhesive securing the cable to the logic board.
Step 8:
Use a T3 Torx driver to remove the two 1.3 mm screws securing the USB-C port connector bracket.
Remove the USB-C connector bracket.
Step 9:
Use the flat end of a spudger to pry the USB-C cable connector up and out of its socket on the logic board.
Step 10:
Use a spudger to lift up the small locking flap on the sound board cable's [https://www.ifixit.com/Guide/Recognizing+&+Disconnecting+Cable+Connectors/25629#s64969|ZIF connector|new_window=true].
Slide the sound board cable out of the ZIF connector.
Step 11:
Peel back the black tape covering the fan cable connector.
Step 12:
Use the tip of a spudger to lift up the locking flap on the fan cable's ZIF connector.
Slide the fan cable out of the ZIF connector.
Step 13:
Use a T3 Torx driver to remove the two 1.4 mm screws securing the antenna cable bracket.
Remove the antenna cable bracket.
Step 14:
Insert the point of a spudger under one of the antenna cables close to the connector. Pry straight up to disconnect the cable.
Repeat for the other antenna cable.
Step 15:
Use a T3 Torx driver to remove the two 1.5 mm screws securing the display cable connector bracket.
Remove the display cable connector bracket.
Step 16:
Use the flat end of a spudger to pry up the display cable connector.
Step 17: Unscrew the logic board
Use a T5 Torx driver to remove the following screws:
One 5.5 mm screw
Three 2.6 mm screws
Two 1.9 mm screws
Step 18: Remove the logic board
Remove the logic board.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $180-$480)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($300-$800)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your MacBook Air 13" 2019 instead of replacing it, you're preventing approximately 155 kg of CO₂ emissions. Manufacturing a new MacBook Air 13" 2019 generates 175 kg of CO₂, while this repair only produces about 20 kg of CO₂. That's a 89% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your MacBook Air 13" 2019 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.