HP Envy 2019 Battery Replacement
Complete guide to HP Envy 2019 battery replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Battery Replacement is one of the most common repairs for HP Envy 2019. This repair involves replacing the damaged power component with a new or refurbished part. The process typically takes 30 min - 1 hour and requires moderate skill level.
🔧 Required Tools
🔩 Replacement Parts
What You'll Need
- Replacement power part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Plug in your computer to charge and take a look at the light coming from near the charging port.
If the light is a steady orange or white, your computer should be charging normally and this guide is no longer necessary.
If the light is a blinking white, your computer is not charging properly and you should proceed to the next step.
Step 2:
Flip the laptop over on its back and remove the two depressed stickers in the middle to reveal the two central 6.0 mm Phillips-head screws.
Step 3:
Use a spudger to pry up the two rear feet near the hinge.
You don't need to pry up the two feet near the front of the laptop as there are no screws underneath them.
Step 4:
Use a Phillips screwdriver to remove the 14 screws securing the back cover.
Step 5:
Once all of the screws have come out, flip the laptop over and open the lid so that the keyboard is face up.
Pop the keyboard from the sides and carefully lift it off of the parts underneath.
'''DO NOT''' pull the keyboard away from the rest of the laptop too quickly. There are various cords and wires connecting the keyboard section to the rest of the computer that should remain plugged in.
Step 6:
Carefully lay the keyboard section against the open screen of your laptop without unplugging anything.
Check the inside of your laptop to make sure there are no glaringly obvious problems (insects, missing parts, scorched parts).
Step 7:
Locate the battery and the three 4.0 mm Phillips-head screws that hold it in place.
Unscrew these three screws and use the tab attached to the battery to remove it safely from the laptop.
Unplug the cord attaching the battery to the motherboard. This is the only cord that should be unplugged throughout the entire fix.
Step 8:
Once the battery is safely removed, plug the charging cord into the charging port on the side and plug the other end into the wall.
'''DO NOT''' turn the computer on or touch any of the internal components during this step.
If the light is on after plugging it in, you have just confirmed that something is wrong with the battery, which means you're on the right track!
If the light on the side blinks upon plugging it in, the battery is not the problem. If that is the case, put your laptop back together and consult an expert.
Unplug the charging cable.
Step 9:
Place the battery back where it was previously and find where it was plugged in.
''Due to general wear and tear, often this will become slightly unplugged, causing the laptop to fail to charge properly.''
Plug the cable on the battery back into the port on the motherboard and make sure it is secured.
Step 10:
Run the earlier test from Step 7 that you performed on the laptop with the battery inside.
'''DO NOT''' turn the computer on or touch any of the internal components during this step.
If the light comes on and doesn't blink, you have fixed the problem! Congratulations!
If the light still blinks, you may have to purchase a new battery for your laptop.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $30-$120)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($50-$200)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your HP Envy 2019 instead of replacing it, you're preventing approximately 260 kg of CO₂ emissions. Manufacturing a new HP Envy 2019 generates 265 kg of CO₂, while this repair only produces about 5 kg of CO₂. That's a 98% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your HP Envy 2019 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.