Google Pixel 8 Pro Logic Board Repair

Let your Pixel's battery drain below 25% before starting this repair. A charged lithium‑ion battery may catch fire if damaged.

Unplug all cables from your phone.

Completely power off your phone.

Press the power and volume up buttons at the same time to bring up the shutdown menu.

Firmly press a SIM eject tool, bit, or straightened paper clip into the SIM card tray hole on the left edge of your phone until the tray ejects.

Remove the SIM card tray.

You'll be using opening picks to separate the screen from the frame. If inserted too far, a pick can damage your device. Follow this step to mark your pick and prevent damage.

Measure 3 mm from the tip and mark the opening pick with a permanent marker.

Alternatively, [link|https://guide-images.cdn.ifixit.com/igi/pQGATIGUbViSB4gB.full|tape a coin to a pick|new_window=true] 3 mm from the tip.

Glass shards can complicate disassembly—or worse, cause injury. If your phone has a cracked screen, follow these steps:

Apply overlapping strips of packing tape to the cracked glass until the whole screen is covered.

Only cover the glass itself—don't stick any tape to the frame.

Wear safety glasses to protect your eyes from any glass shaken free during the repair.

Adhesive and clips secure the screen to the frame. Heating the screen softens the adhesive, making it easier to separate.

Alternatively, you can use a [guide|157348|hair dryer|new_window=true], [guide|151116|heat gun|new_window=true], or hot plate—but be careful as extreme heat can damage the screen and/or battery.

The next three steps demonstrate the [product|IF145-513|Anti-Clamp], a tool we designed to make the opening procedure easier. ***If you aren't using the Anti-Clamp, skip down three steps for an alternate method.***

For complete instructions on how to use the Anti-Clamp, [guide|152309|check out this guide|new_window=true].

Pull the blue handle backwards to unlock the Anti-Clamp's arms.

Place your phone screen side up on an object so it will rest level between the Anti-Clamp's arms—the bottom edge should be hanging off.

Slide the arms over the left edge of your phone, so you have access to the bottom edge.

Position the suction cups as close to the center of the bottom edge as possible.

Squeeze the cups together to create suction.

Pull the handle forward to lock the arms.

Turn the handle clockwise ***one full turn*** (360 degrees), or until the suction cups begin to stretch.

As the cups stretch, make sure they stay aligned with each other. If they keep slipping, remove the Anti-Clamp and [guide|159595|apply tape for the cups to stick to|new_window=true].

Wait one minute for a gap to form between the screen and frame.

If the adhesive doesn't separate, twist the handle clockwise ***one quarter turn*** and wait another minute. Apply more heat if the screen cools down.

Insert an opening pick into the gap.

Don't insert your opening pick more than ***3 mm*** to avoid damaging the spring contacts.

Pull the blue handle backwards to unlock the arms and remove the Anti-Clamp using the pull tabs on the suction cups.

***Skip the next two steps***.

Apply a suction handle to the center of the screen's bottom edge.

Pull up on the suction handle with strong, steady force until a gap forms between the screen and frame.

If you're having trouble creating a gap, apply more heat and try again.

Insert an opening pick into the gap.

To avoid damaging your phone, ***don't insert your pick more than 3 mm as you separate the screen adhesive***. Note the following areas:

The screen cable is a little less than halfway up the left edge of the phone. Be very careful here to avoid tearing the cable.

There are many spring contacts around the perimeter of the phone. Be very careful in these areas to avoid bending the contacts.

Slide the opening pick along the bottom edge to separate the adhesive securing it.

Leave the pick in the bottom right corner to prevent the adhesive from resealing.

Apply a [guide|25705|heated iOpener|new_window=true] to the right edge of the screen for two minutes.

Alternatively, you can use a [guide|157348|hair dryer|new_window=true], [guide|151116|heat gun|new_window=true], or hot plate—but be careful as extreme heat can damage the screen and/or battery.

Insert a second opening pick under the bottom right corner of the screen.

Slide the new pick to the top right corner to separate the adhesive securing the screen's right edge.

Leave the pick in the top right corner to prevent the adhesive from resealing.

Insert a third opening pick under the bottom edge of the screen.

Slide the new pick to the bottom left corner.

Leave the pick in the bottom left corner to prevent the adhesive from resealing.

Apply a [guide|25705|heated iOpener|new_window=true] to the left edge of the screen for two minutes.

Alternatively, you can use a [guide|157348|hair dryer|new_window=true], [guide|151116|heat gun|new_window=true], or hot plate—but be careful as extreme heat can damage the screen and/or battery.

Insert a fourth opening pick under the bottom left corner of the screen.

Slide the new pick to the top left corner to separate the adhesive securing the screen's left edge.

Leave the pick in the top left corner to prevent the adhesive from resealing.

Apply a [guide|25705|heated iOpener|new_window=true] to the top edge of the screen for two minutes.

Alternatively, you can use a [guide|157348|hair dryer|new_window=true], [guide|151116|heat gun|new_window=true], or hot plate—but be careful as extreme heat can damage the screen and/or battery.

Insert a fifth opening pick under the top edge of the screen, near the left corner.

Slide the opening pick to the top right corner to separate the adhesive securing the screen's top edge.

Place a small box or stack of books to the left of your phone so you can prop up the screen while disconnecting its cable.

Swing up the right edge of the screen like the front cover of a book.

If the screen feels stuck, go back around the perimeter with an opening pick to separate any remaining adhesive.

Prop up the screen so you can access the screen cable without straining it.

Use an opening tool to pry up the upper edge of the [link|https://guide-images.cdn.ifixit.com/igi/dAUmC6lHA33IxMIJ.full|screen cable cover|new_window=true].

Remove the cover.

Insert the point of a spudger under the top right corner of the screen's press connector.

Gently pry up and disconnect the cable.

Remove the screen.

To reconnect a [guide|25629|press connector|stepid=70308|new_window=true], align it over its socket and gently press down on one side until it clicks into place, then press down on the other side. Don't press down in the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

***The back of the Pixel's screen is very fragile. Even a small scratch or dent can damage the screen.***

To prevent damaging your screen or replacement screen:

When handling your screen, grip it by its edges.

When placing the screen on your work area, make sure nothing is touching the bottom of the screen. Consider placing it on a soft, lint-free cloth.

If you're installing a new screen with pre-installed adhesive, follow this step ''during reassembly''. Otherwise, follow [guide|165811|this guide|new_window=true] to apply adhesive to your old screen.

Thoroughly check the ''entire'' screen for any plastic liners or tape and use the pull tabs to remove all of them. Look carefully for a large piece of plastic covering the back of the screen, a small one near the front camera cutout, and adhesive liners around the perimeter.

Reconnect the screen cable and reinstall its cover.

This is a good point to test your phone before sealing it up. Temporarily power on your phone and make sure it works as expected. Power it down before continuing.

Firmly press the screen into place on the frame—you should feel the clips "pop" into place.

Press firmly around the perimeter of the screen to secure it with the new adhesive.

Optionally, you can strengthen the adhesive bond by [guide|165811|applying pressure evenly to the phone|stepid=349253|new_window=true].

Follow [guide|166753|this guide|new_window=true] to calibrate the fingerprint sensor.

The next few steps show how to disconnect and detach the [link|https://guide-images.cdn.ifixit.com/igi/loYsQdl3FPnf62qU.full|5G mmWave antenna cable|new_window=true]. If your phone doesn't have a 5G mmWave antenna, ***skip the next four steps***.

Be very careful not to scrape off or damage any [link|https://guide-images.cdn.ifixit.com/igi/tDlrDUoT1fSvaEkl.full|surface mounted components|new_window=true] during this step.

Insert the tip of a spudger under the top edge of the 5G mmWave antenna's press connector.

Gently pry up and disconnect the cable.

Alternatively, you can use a [guide|157348|hair dryer|new_window=true], [guide|151116|heat gun|new_window=true], or hot plate—but be careful as, extreme heat can damage the battery.

Insert the flat end of a spudger between the bottom of the 5G mmWave antenna cable and the midframe, just above the press connector.

Twist the spudger to separate the bottom of the cable from the midframe.

Grip the bottom of the 5G mmWave antenna cable and gently peel it from the midframe.

During reassembly, press the cable back into place on the midframe to secure it with the old adhesive. If it doesn't stick, use [product|IF317-072|thin, double-sided tape|new_window=true] to secure it.

A [link|https://guide-images.cdn.ifixit.com/igi/wT1rCvsyGqZr34oj.full|large graphite sheet|new_window=true] must be removed ''and replaced'' to complete this repair. It connects the upper part of the battery, midframe, and the rear cameras.

Insert the point of a spudger under different parts of the graphite sheet and lift until you can grip the sheet with your fingers.

The sections of graphite sheet between the rear cameras and the battery will most likely tear. If they do, grip the broken part of the sheet and remove that section.

Peel up and remove the entire graphite sheet.

During reassembly, do ***not*** reuse the old graphite sheet. Follow [guide|165973|this guide|new_window=true] to replace the sheet.

Use the tip of a spudger to gently lift the plastic shim that runs along the top of the USB-C port cover.

Remove the shim and set it aside or move it out of the way so you can access the USB-C port cover screws.

During reassembly, follow this step to replace the plastic shim that runs across the bottom of the midframe and loudspeaker. If you don't have a replacement, press the old one back into place.

Remove the larger rectangular liner from the shim.

Place the shim so the smaller piece of foam [link|https://guide-images.cdn.ifixit.com/igi/Xb2WTEJYmTdrn3Wa.full|lines up with the bottom of the USB-C port cover|new_window=true].

Use the flat end of a spudger to [link|https://guide-images.cdn.ifixit.com/igi/NdLZOED1xxXQQKqu.full|firmly press down along the whole shim|new_window=true] to secure it.

Remove the remaining liner.

Throughout this repair, [product|IF145-491|keep track of each screw|new_window=true] and make sure it goes back exactly where it came from.

While the Pixel 8 Pro uses [link|https://en.m.wikipedia.org/wiki/Torx#Torx_Plus|Torx Plus|new_window=true] screws, standard Torx bits will also work. Make sure to apply constant, downward force to prevent stripping.

Use a T3 Torx screwdriver to remove the two 5 mm‑long 3IP Torx Plus screws securing the USB‑C port cover.

Remove the cover.

Use a T3 Torx screwdriver to remove the seven 5 mm‑long 3IP Torx Plus screws securing the midframe.

Remove the midframe.

During reassembly check the condition of the thermal pad. If it's damaged, remove the pad, clean the area with high-concentration (greater than 90%) isopropyl alcohol and a microfiber or lint-free cloth, and apply a new thermal pad.

Use the point of a spudger to pry up and disconnect the battery cable press connector.

Use the point of a spudger to pry up and disconnect the front camera press connector.

Remove the front camera.

Use the point of a spudger to pry up and disconnect all three rear camera press connectors from the top edge of the logic board.

You may need to hold the 5G mmWave antenna cable out of the way while removing the rear camera assembly screws.

Use a T3 Torx screwdriver to remove the two screws securing the rear camera assembly:

One 3.5 mm‑long 3IP Torx Plus screw securing the top left corner

One 5 mm‑long 3IP Torx Plus screw securing the top right corner

Insert a spudger between the right edge of the rear camera assembly and frame.

Pry the rear camera assembly up and remove it.

Use a T3 Torx screwdriver to remove the two 5 mm‑long 3IP Torx Plus screws securing the 5G mmWave antenna bracket.

Insert the tip of a spudger in one of the 5G mmWave antenna bracket's screw holes.

Pry up with the spudger to dislodge the bracket.

Remove the bracket.

During reassembly, insert the bracket at a downward angle so the [link|https://guide-images.cdn.ifixit.com/igi/GomeYdHjlRD56Zmv.full|spring contacts and foam pads|new_window=true] press up against the 5G mmWave antenna. Press the bracket down to secure it.

Grab the 5G mmWave antenna cable and gently lift the antenna out of its recess.

If the cable disconnects from the antenna, don't worry! Use your fingers to remove the antenna. ''Make sure to reconnect the antenna cable during reassembly''.

Insert one arm of a pair of [product|IF145-020-5|angled tweezers] under the metal neck of the black antenna cable [guide|25629|coaxial connector|stepid=64972|new_window=true], located on the top left corner of the logic board.

Gently lift straight up to disconnect the cable.

To reconnect the cable, hold the connector in place over its socket and press down with the flat end of a spudger—the connector should snap into place. If you're having trouble, don't try to force the connector over the socket. Reposition it and try again.

Insert one arm of a pair of [product|IF145-020-5|angled tweezers] under the metal neck of the white antenna cable coaxial connector, located on the top left corner of your phone.

Gently lift straight up to disconnect the cable.

Gently pull the white antenna cable out of its clip on the left side of your phone.

Use the point of a spudger to pry up and disconnect the interconnect and ultra-wideband press connectors from the top left corner of the logic board.

Use a T3 Torx screwdriver to remove the 5 mm‑long 3IP Torx Plus screw securing the loudspeaker.

Insert the point of a spudger between the bottom right edge of the loudspeaker and frame.

Pry the loudspeaker up with the spudger to dislodge it from its recess.

Remove the loudspeaker.

During reassembly, insert the edge of the loudspeaker with an orange gasket at a downward angle into its recess. Then press the loudspeaker firmly into place.

Adhesive secures the battery to the frame. Heating the back cover softens the adhesive, making it easier to separate.

Carefully flip your phone over and lay it down on your workspace.

Use a [guide|157348|hairdryer|new_window=true] or [guide|151116|heat gun|new_window=true] to heat the left side of the back cover, where the battery is located. It should be slightly too hot to touch.

Be careful not to heat the phone hotter than this—the battery is susceptible to heat damage.

Flip your phone back over and lay it on your workspace.

Apply a few drops of highly-concentrated isopropyl alcohol along the right edge of the battery.

Tilt your phone to help the alcohol flow towards [link|https://guide-images.cdn.ifixit.com/igi/sBRPnsZOUIu1mYKw.full|the adhesive on the top and bottom edges of the battery|new_window=true].

Wait one minute to allow the alcohol to dissolve the adhesive.

Insert the flat side of an opening pick between the right edge of the battery and frame.

Take care not to crease or bend the battery—it can leak dangerous chemicals and/or catch fire.

The adhesive securing the battery is ''***very***'' strong. Separating it requires ''time'' and ''constant pressure''. It will most likely take multiple rounds of heat and isopropyl alcohol.

Firmly secure your phone with one hand.

With your free hand, pry the battery up with the pick. Maintain constant pressure on the pick until the battery separates from the frame.

If after two minutes of constant pressure the battery doesn't budge, apply more heat and isopropyl alcohol and try again.

Use the opening pick to lift the battery and separate the remaining adhesive.

Remove the battery.

During reassembly:

If your battery is creased, bent, or deformed, ***do not reuse it***—it's a fire hazard. Replace it with a new battery.

Follow [guide|166151|this guide|new_window=true] to remove the old adhesive and install your battery.

Use a T3 Torx screwdriver to remove the 2.5 mm‑long 3IP Torx Plus screw securing the grounding bracket to the bottom right edge of your phone.

Remove the grounding bracket.

Use a T3 Torx screwdriver to remove the 3.5 mm‑long 3IP Torx Plus screw securing the logic board.

Before removing the logic board, make sure the SIM card tray is removed.

Lift the top edge of the logic board and remove it, making sure no cables get snagged on the board.

During reassembly:

Make sure the [link|https://guide-images.cdn.ifixit.com/igi/IkYjv5IuEvrjmyJy.full|interconnect, ultra-wideband, and black antenna cables|new_window=true] are out of the way ''before'' putting the board into place.

Insert the board at a downward angle so the USB‑C port goes into its recess in the bottom of the frame.

Lay the top of the board down and push it into its recess.

Flip the logic board over and lay it down on a soft, clean surface such as a towel to prevent damaging it.

Insert one arm of a pair of angled tweezers under the metal neck of the white antenna cable coaxial connector, located on the bottom of the logic board.

Gently lift straight up to disconnect the cable.

Gently pull the white antenna cable out of its clips on the bottom of the logic board.

Remove the antenna cable.

During reassembly, use the point of a spudger to [link|https://guide-images.cdn.ifixit.com/igi/CZy6mcmcnPRAleUK.full|gently push the cable back into its clips|new_window=true].

You're left with the logic board.