Google Pixel 5a Battery Replacement

Be sure to turn off your device before you begin the repair.

You'll need to pry the screen up to remove it from the phone. Read the following notes carefully before proceeding.

Take note of the two seams on the edge of the phone:

''Screen seam'': This seam separates the screen from the rest of the phone. ***Do not pry at this seam.***

''Bezel seam'': This is where the plastic bezel designed to protect the screen meets the frame. It's held in place by plastic clips. ***This is where you should pry.***

Depending on the strength of your device's adhesive, you may need to reapply the iOpener multiple times in order to weaken it enough.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

To remove the screen, you'll need to insert opening picks in between the black clips that secure the bezel to the midframe.

Note the optimal points of entry before proceeding.

If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

Place a suction cup as close to the right edge of the screen as possible.

Lift the suction cup with a strong steady force until a small gap forms between the bezel and midframe.

The bezel is connected to the midframe by a series of plastic clips which can be detached by inserting an opening pick at points all along the seam.

Insert the tip of an opening pick into the ''bezel seam'' about 4-5 cm from the bottom of the phone.

Insert the tip of an opening pick into the ''bezel seam'' about 3-4 cm from the top of the phone.

Insert the tip of an opening pick into the ''bezel seam'' at the top of the phone.

If this step proves difficult, slide the pick along the top right corner of the phone until there is enough of a gap at the top for the opening pick.

Insert the tip of an opening pick into the ''bezel seam'' at the bottom of the phone.

If this step proves difficult, slide the pick along bottom right corner of the phone until there is enough of a gap at the bottom for the opening pick.

Insert the tip of an opening pick into the ''bezel seam'' on the left side of the phone, about 2 cm from the bottom of the phone.

Insert the tip of an opening pick into the ''bezel seam'' about 3-4 cm below the front-facing camera.

Be sure to detach all the clips. Slice through any remaining adhesive with an opening pick.

Open the device from the right side like a book.

Use a T3 Torx driver to remove the 4.6 mm-long screw securing the screen connector bracket.

Throughout this repair, [https://www.ifixit.com/Store/Tools/Magnetic-Project-Mat/IF145-167-4|keep track of each screw|new_window=true] and make sure it goes back exactly where it came from.

Use a pair of [product|IF145-020|tweezers] to remove the screen connector bracket.

Use the tip of a spudger to pry up and disconnect the screen flex cable.

To re-attach [https://www.ifixit.com/Guide/Recognizing+&+Disconnecting+Cable+Connectors/25629#s70308|new_window=true|press connectors] like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

***The back of the Pixel's screen is very fragile. Even a small scratch or dent can damage the screen.***

To prevent damaging your screen or replacement screen:

When handling your screen, grip it by its edges.

When placing the screen on your work area, make sure nothing is touching the bottom of the screen. Consider placing it on a soft, lint-free cloth.

Remove the screen from the phone.

During reassembly:

If you replaced the screen, check the screen's front-facing camera hole and remove any protective liners covering it.

***Remember to reinstall the screen connector bracket.***

If you are using a custom-cut adhesive, follow [guide|155756|this guide|new_window=true] to correctly apply new screen adhesive.

If you are using Tesa tape to reattach the screen, [guide|113604|follow this guide].

During the boot-up process after reassembly, the screen will go through a calibration sequence. Do not touch the screen during this process, as it could result in improper touch calibration and create touch issues.

Use a T3 Torx driver to remove six of the screws securing the midframe to the motherboard:

Four 4.6 mm screws

One 4.0 mm screw

One 2.0 mm screw

Since a few of these screws have different lengths, keep track of each screw and be sure to reinstall them in their proper places.

Use the pointed end of a spudger to pry up on the black plastic cover at the bottom left of the phone.

Slide the pointed end of the spudger left until the plastic cover is completely separated from the midframe.

Remove the plastic cover from the midframe.

Use a pair of [product|IF145-020|tweezers] to slightly peel back the tape concealing the two screws securing the charging port bracket.

Use a T3 Torx driver to remove the remaining four screws securing the midframe to the motherboard:

Three 4.6 mm screws

One 4.0 mm screw

Use a spudger or a pair of tweezers to peel back the tape securing the charging port bracket to the speaker assembly.

Take care not to puncture or bend the battery with your tool—a punctured or bent battery may leak dangerous chemicals or cause a fire.

Use a ***blunt*** pair of tweezers, or your fingers, to carefully peel back the graphite sheet covering the battery.

Be careful not to accidentally puncture or otherwise damage the battery when gripping the graphite sheet.

Insert the pointed end of a spudger under the top right corner of the midframe.

There is a black plastic clip at the top of the midframe that secures it to the top of the frame. To detach it, use the spudger to pull the midframe down and then pry up.

Remove the midframe.

There are two small plastic bits that help hold the midframe in place. Take care not to misplace them, as without the midframe to hold them in place, they are very easy to lose.

Be sure to place these back into their respective corners ***before*** replacing the midframe when reassembling your device.

Use the flat end of a spudger to pry up on the battery connector to disconnect it.

If you are using adhesive remover, [https://www.ifixit.com/Guide/iFixit+Adhesive+Remover+Preparation/118537|follow these preparation steps first|new_window=true].

Apply 2-3 drops of high concentration (90% or higher) isopropyl alcohol under each corner of the battery and allow it to penetrate for 2-3 minutes to help weaken the adhesive.

Insert a pick into the gap to the right of the battery and slide its tip underneath the battery.

Take care not to puncture or bend the battery with your tool—a punctured or bent battery may leak dangerous chemicals or cause a fire.

Slide the pick along the right side of the battery to slice through the adhesive securing it to the midframe.

Once the right side of the battery begins to separate from the midframe, leave an opening pick in the gap to keep the battery slightly raised.

Apply a few drops of isopropyl alcohol directly to the adhesive securing the battery to the midframe. Let the isopropyl penetrate the adhesive for 2-3 minutes.

Repeat the last step with an opening card to slice through the remaining adhesive under the right side of the battery.

Remove the battery.

Do not reuse the battery after it has been removed. The stress of removal can cause hidden damage to the battery cell, creating a potential safety hazard. Replace it with a new battery.

To install a new battery:

Remove any remaining adhesive from the phone, and clean the entire area under the battery with isopropyl alcohol. If there's any alcohol solution remaining in the phone, carefully wipe it off with a lint-free cloth or allow it to air dry before installing your new battery.

Apply a few new strips of [https://www.ifixit.com/Guide/How+to+Use+a+Pre-Cut+Adhesive+Sheet/113604|pre-cut adhesive|new_window=true] or [https://www.ifixit.com/Store/Tools/Tesa-61395-Tape/IF317-072-1|Tesa tape|new_window=true].

If you are attaching the battery with a custom-cut adhesive, [https://www.ifixit.com/Guide/How+to+Apply+Custom-cut+Battery+Adhesive/123541|follow this guide|new_window=true].

Press the new battery firmly into place for 5-10 seconds.