GE Bottom Freezer Refrigerator Refrigerator Compressor Repair
Complete guide to GE Bottom Freezer Refrigerator refrigerator compressor repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Refrigerator Compressor Repair is one of the most common repairs for GE Bottom Freezer Refrigerator. This repair involves replacing the damaged cooling component with a new or refurbished part. The process typically takes 2-4 hours and requires difficult skill level.
What You'll Need
- Replacement cooling part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Remove Control Panel
Unplug the refrigerator or turn off the breaker for the power circuit it is on. Then remove the Philips screw you see in this photo
Step 2: Pull Off Control Panel
After removing the screw pry off the control panel. Insert a flat head screw driver into the slot shown here and pull the right side of the panel towards you and slightly upward. Clips at sides of the panel will release it. The top of the control panel has a tab that fits into a slot in the door, as shown.
Step 3: Disconnect Panel
Pull the wiring harness clip free from the control panel and put the panel aside.
Step 4: Unplug Water Hose
Pull the water hose free of its slot in the unit and up and out of the dispenser cone.
Step 5: Remove Screws Holding in Unit
There are two brass-colored Philips screws to remove. One is at the top right, visible in this photo, and the other is at the bottom left, not visible here but where the arrow indicates.
Step 6: Disconnect two wiring harnesses
The unit can now be pulled out of the door. Disconnect two wiring harnesses by squeezing down on the tabs that each one has. This will release the clips.
Step 7: Disconnect Paddle Switch
On the right side of the unit is a switch that the paddle presses to activate ice or water flow. Its electric wires slide off. The switch on my old unit fell off the unit, perhaps because the old paddle arm was broken off. Photos show new unit and old switch with wires attached.
Step 8: Connect New Unit Paddle Switch
Old unit should now be completely removed and set aside. Slide the paddle switch wires onto the new unit.
Step 9: Connect Wiring Harnesses and Water Hose
Connect the two wiring harnesses to the new unit. Connect these first and then tuck behind the water hose. Press water hose into its slot on the front of unit. Then feed the end of the water hose into the dispenser cone. Use forefinger inside the cone to guide the hose into its slot down the front of the cone and into the circle holder at bottom
Step 10: Attach Dispenser Unit to Door
Before inserting the brass screws, the tab on the top left of the unit needs to be inserted into its slot to the left of the ice pipe. See arrow. Tilt the top of the unit in to the door, aligning this tab with the slot in the door, and slide it up. Then press unit into place. Check that the two screw holes are aligned and install Philips screws.
Step 11: Reattach Control Panel
The control panel has a tab at top center. Insert this into a slot in the door located above the water hose by tilting the top of the panel into place first. Then press the panel into place on the two sides. Insert the Philips screw.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $120-$270)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($200-$450)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your GE Bottom Freezer Refrigerator instead of replacing it, you're preventing approximately 288 kg of CO₂ emissions. Manufacturing a new GE Bottom Freezer Refrigerator generates 300 kg of CO₂, while this repair only produces about 12 kg of CO₂. That's a 96% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your GE Bottom Freezer Refrigerator and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.