Framework Laptop 16 Keyboard Replacement
Complete guide to Framework Laptop 16 keyboard replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Keyboard Replacement is one of the most common repairs for Framework Laptop 16. This repair involves replacing the damaged input component with a new or refurbished part. The process typically takes 2-4 hours and requires difficult skill level.
What You'll Need
- Replacement input part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Before you begin
Unplug all cables and fully shut down your laptop.
If your repair requires a spudger, a T5 Torx, or a Phillips screwdriver, you can use the included Framework screwdriver. Whichever works best for you!
Step 2: Unlock the Input Modules
Use your fingernail to pull out the two Input Module latches and unlock them.
The latch will show red if it's unlocked.
Step 3: Remove the touchpad spacers
Use your fingers to slide the touchpad spacer toward the bottom edge of the laptop and unclip it.
If you're having trouble, check if the corresponding Input Module latch is properly unlocked.
Lift the touchpad spacer off the laptop and remove it.
Step 4:
Repeat the same procedure for the other touchpad spacer.
Step 5: Remove the touchpad
Use your fingers to slide the touchpad toward the bottom edge of the laptop and disconnect it.
If you're having trouble, check if the Input Module latches are properly unlocked.
Lift the touchpad and remove it.
During reassembly, perform the following:
Place the touchpad flat on its cutout so [link|https://guide-images.cdn.ifixit.com/igi/3IG23UyJJiG66yWx.full|its clips|new_window=true] are properly aligned.
Press the touchpad down and slide it into place so it lines up evenly with the bottom edge of the laptop.
Step 6: Remove the keyboard
The keyboard is held in place with strong magnets. Apply gradually increasing force to avoid having the keyboard violently eject.
Grip the two pull tabs along the bottom of the keyboard.
Lift the pull tabs until the keyboard magnets release.
Remove the keyboard.
During reassembly, make sure the keyboard is seated properly on its [link|https://guide-images.cdn.ifixit.com/igi/yG5pofFao6OSTNba.full|alignment pegs|new_window=true] and sits evenly with the edges of the laptop.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Very easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $120-$360)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($200-$600)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Framework Laptop 16 instead of replacing it, you're preventing approximately 250 kg of CO₂ emissions. Manufacturing a new Framework Laptop 16 generates 265 kg of CO₂, while this repair only produces about 15 kg of CO₂. That's a 94% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Framework Laptop 16 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.