Acer Aspire 5 Water Damage Repair
Complete guide to Acer Aspire 5 water damage repair. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Water Damage Repair is one of the most common repairs for Acer Aspire 5. This repair involves replacing the damaged recovery component with a new or refurbished part. The process typically takes 2-4 hours and requires difficult skill level.
What You'll Need
- Replacement recovery part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Turn off and unplug your Acer Aspire 5 A515-54.
Flip it over so the backside is facing up.
Step 2:
Use the Phillips #0 screwdriver to remove eleven 9 mm screws securing the back cover.
Use a prying tool to gently open the back cover of the laptop.
Step 3:
Be sure to ground yourself or wear an antistatic bracelet to avoid static discharge and damage to the motherboard.
Disconnect the battery by gently pulling out the connector.
Step 4:
Notice there is a mounting tray with a cable for the additional HDD. Remove the four 3 mm screws with a Phillips #0 screwdriver.
Take out the mounting tray and connector to prepare for the hard drive installation in the next step.
Step 5:
Take the connector from previous step and connect it to the new hard drive.
Insert the drive into the mounting tray.
Step 6:
There are 2 mm screws that come with the laptop box.
Use the Phillips #0 screwdriver to secure the 2 mm screws to the mounting tray, which holds the HDD .
Step 7:
Slide the mounting bracket with the hard drive into the socket (with the cable facing towards the battery).
Use the Phillips #0 screwdriver to replace the 3 mm screws and hold the bracket in place.
Step 8:
Use the Phillips #0 screwdriver to remove the single screw attaching the wireless card to the motherboard.
Gently slide the wireless card out of the socket and set it aside in order to connect the hard drive to the motherboard.
Step 9:
Gently insert the hard drive cable into the connector on the motherboard and lock it in place.
Slide the wireless card back into the socket and using the Phillips #0 screwdriver, secure with the single screw.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $60-$240)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($100-$400)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your Acer Aspire 5 instead of replacing it, you're preventing approximately 245 kg of CO₂ emissions. Manufacturing a new Acer Aspire 5 generates 255 kg of CO₂, while this repair only produces about 10 kg of CO₂. That's a 96% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your Acer Aspire 5 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.