Skip to main content
🔧
HowMuchToFixAI for a Greener Future
Engine
moderate

2025 Ford Escape Spark Plug Replacement

Complete guide to 2025 Ford Escape spark plug replacement. Cost estimates, difficulty level, time required, and environmental impact.

💰 Cost:$100 - $200
⏱️ Time:1-2 hours
🌍 CO₂ Saved:6198 kg

🌍 Share Your Environmental Impact

Inspire others to repair instead of replace! Share how much CO₂ you're saving.

Share your impact:

💰 Cost Breakdown

Parts$60 - $120
Labor$40 - $80
Total Estimated Cost$100 - $200

💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.

🔧 Repair Overview

Spark Plug Replacement is one of the most common repairs for 2025 Ford Escape. This repair involves replacing the damaged engine component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.

🔧 Required Tools

🔩 Replacement Parts

What You'll Need

  • Replacement engine part (OEM or aftermarket)
  • Precision screwdriver set (Phillips #000 or pentalobe)
  • Opening tools (plastic spudger, suction cup)
  • Adhesive strips or glue
  • Clean workspace with good lighting

Step-by-Step Process

Step 1: Remove Shroud

Step 1 - Image 1
Step 1 - Image 2

3 5/16 screws hold the shroud in place

Loosen Screws and remove or if you cant get the loose screws out because the holes are deep, cover the holes with tape and remove the shroud. you may have to wiggle it to get it out

Step 2: Top of Coils are numbered and Electrical Cable

Step 2 - Image 1
Step 2 - Image 2

The image is marked for coils 4, 5 and 6 which you will see once the shroud is off. you may as well replace all 3 but if money is a factor, then just replace the bad one.

Press on the clip lock on the electrical cable where you see my thumb nail to release the lock and just pull to slide off.

Step 3: Remove Anchor Bolt that holds the coil in place

Step 3 - Image 1
Step 3 - Image 2

Remove the 3 bolts that holds the 3 coils in place

If the bolts are tight because they've been in a while, use pb blaster to penetrate and give it some time to loosen. pb blaster is better than wd-40

then pull the coils straight out. There might be a little resistance as it separates from the spark plug but it should just come right out.

Coils have a plastic top with an electrical connector and a rubber boot on the bottom. This eliminates the old style when we used to have a cap and wires to make the connection

Step 4: Remove the spark plugs

Step 4 - Image 1
Step 4 - Image 2

Make sure you use an actual spark plug socket that has a rubber insert so that the plug will come out with the socket.

Take note of the direction of the plugs when you take them out, gap / screw side down

The new plugs wont need to be gapped.

Loosen slowly and when tightening, tighten slowly. Do not over tighten.

I used ENA brand coils that I got on Amazon. Was 6 for $45 and the plugs were $38.

Step 5: Assemble in reverse order - Final words

Step 5 - Image 1

Assemble in reverse order. When properly seated and bolted back in, coils should be all the way down so the anchor bolt and plastic head of the coil is flush with the engine where it is seated.

The bolt should be tight but do not over tighten. you may want to put a tiny tiny bit of pb blaster on the bolt to help it especially if it squeels as you tighten it. You don't want to break the bolt or over tighten.

After everything is back together test drive the car. You should notice that the misfires are gone but the check engine light wont go out until the car has enough recordings of no-misfires usually several 20 minute drives.

📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.

iFixit Difficulty: Very easy | Time: NaNh NaNm

DIY vs Professional Repair

✋ DIY Repair

  • ✅ Lower cost (parts only: $60-$120)
  • ✅ Learn new skills
  • ❌ Risk of further damage
  • ❌ No warranty
  • ❌ Requires tools and time

🔧 Professional Repair

  • ✅ Expert installation
  • ✅ Warranty included
  • ✅ Faster turnaround
  • ❌ Higher cost ($100-$200)
  • ❌ Need to find reputable shop

Environmental Impact

By choosing to repair your 2025 Ford Escape instead of replacing it, you're preventing approximately 6198 kg of CO₂ emissions. Manufacturing a new 2025 Ford Escape generates 6200 kg of CO₂, while this repair only produces about 2 kg of CO₂. That's a 100% reduction in carbon emissions!

Get a Personalized Repair Estimate

Upload a photo of your 2025 Ford Escape and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.

Related Repair Guides