2022 Subaru Forester Brake Pad Replacement
Complete guide to 2022 Subaru Forester brake pad replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Brake Pad Replacement is one of the most common repairs for 2022 Subaru Forester. This repair involves replacing the damaged brakes component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
What You'll Need
- Replacement brakes part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Park your car on a level surface.
Make sure to put the car in park (first gear for manual transmissions) with the emergency brake engaged.
Do not change oil within 2 hours of driving the car to allow the oil time to cool.
Step 2:
Place the oil pan under the oil drain plug. (this is located under the front end of the car)
You may choose to protect the ground with a tarp or piece of cardboard.
Step 3:
Unscrew the oil drain plug with the 17mm wrench. This is located under the front of the car in the gap in the bottom panel.
Adjust the placement of the oil pan if necessary.
Allow the oil to completely drain into the oil pan.
Wear clothes that you would not mind getting oil on.
Step 4:
After letting the oil drain for 10 minutes unscrew and remove the oil filter. This is located to the right of the engine when the hood is opened.
Place the old oil filter in the oil filter disposal bag.
Step 5:
Coat the o-ring of the new filter with oil to ensure a good seal.
Screw the new filter into place.
Step 6:
When reinstalling the oil drain plug, replace the crush washer (part# 803916010) .
Tighten the oil drain plug to 32 ft/lbs of torque.
Step 7:
Unscrew cap for engine oil. This is located directly to the left of the oil filter.
Place a clean funnel in the tube.
Slowly fill with the 5.1 quarts of engine oil.
Screw the engine oil cap back on.
Step 8:
Pour the oil from the pan into the empty milk jug.
Your local waste disposal company will recycle this for you.
Step 9:
Allow the car to run for 10 minutes in idle.
Check the oil level with the dipstick. This is located to the right of the engine when the hood is opened.
Check under the car for any dripping liquids.
You have completed an oil and filter change on your 2015 Subaru Forester.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $90-$180)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($150-$300)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your 2022 Subaru Forester instead of replacing it, you're preventing approximately 5795 kg of CO₂ emissions. Manufacturing a new 2022 Subaru Forester generates 5800 kg of CO₂, while this repair only produces about 5 kg of CO₂. That's a 100% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your 2022 Subaru Forester and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.