2020 Hyundai Santa Fe Brake Pad Replacement
Complete guide to 2020 Hyundai Santa Fe brake pad replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Brake Pad Replacement is one of the most common repairs for 2020 Hyundai Santa Fe. This repair involves replacing the damaged brakes component with a new or refurbished part. The process typically takes 1-2 hours and requires moderate skill level.
What You'll Need
- Replacement brakes part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Open the trunk.
Remove the black plastic cover located on the inner side taillight by using a #2 flat head screwdriver.
Make sure to pry it off gently to avoid cracking the plastic cover.
Step 2:
Remove the two 12 mm Phillips # 2 screws holding the taillight in place.
Step 3:
Slide out the headlights placing one hand on the outer side and the other hand gripped onto the back of the taillight, pulling straight out.
For easier removal, press down with force on the outer side of the headlight.
Step 4:
Turn the grey brake light socket with the multi-colored wires connected to it counterclockwise.
Step 5:
Pull out the light bulb from the grey bulb socket by pushing downwards while turning counterclockwise.
Step 6:
Take the new replacement bulb and insert it into the light socket while pushing down onto the bulb, turning clockwise and securing the bulb in place.
Step 7:
Slide the light socket back into the circular compartment, making sure the bulb is facing inwards.
After inserted, turn it clockwise to lock the bulb back into place.
Step 8:
Slide the taillight back into the starting position.
Align the taillight with a circular piece on the outer side of the car.
Use moderate force while sliding the taillight, making sure screw holes are visible.
Make sure the grey circular piece on the side is aligned with the taillight to avoid damaging the taillight.
Step 9:
Take the two 12 mm Phillip #2 screws and place them back into the two visible holes.
Step 10:
Replace the plastic cover by pushing down on all of the corners.
Once the plastic piece is fixed onto the car, you can then close the trunk.
The plastic piece is secure when all the sides are lined up with the car and taillight.
Avoid applying a significant amount of force to prevent cracks in the plastic.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $90-$180)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($150-$300)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your 2020 Hyundai Santa Fe instead of replacing it, you're preventing approximately 5695 kg of CO₂ emissions. Manufacturing a new 2020 Hyundai Santa Fe generates 5700 kg of CO₂, while this repair only produces about 5 kg of CO₂. That's a 100% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your 2020 Hyundai Santa Fe and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.