2020 Honda Accord Tire Rotation
Complete guide to 2020 Honda Accord tire rotation. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Tire Rotation is one of the most common repairs for 2020 Honda Accord. This repair involves replacing the damaged tires component with a new or refurbished part. The process typically takes 30-45 min and requires easy skill level.
What You'll Need
- Replacement tires part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
Press the trunk lever button on the driver's side door to open the trunk.
Alternately, press and hold the trunk release button on the key fob for 3-5 seconds to open the trunk.
Step 2:
There is a little grey/black plastic trim cover behind the taillight that will need to come off.
Using a plastic pry bar, pry out on the edge (top and bottom) of the plastic trim cover to remove it.
You could also stick your flat head screwdriver behind the plastic cover and gently pull it from the top and then from the bottom.
Step 3:
Remove the two 8 mm screws behind the tail light assembly using a Phillips #2 screwdriver.
Step 4:
Remove the taillight assembly by sliding or pushing the taillight towards the outside of the car.
Apply gentle force to remove the taillight to prevent it from breaking.
Step 5:
Unplug the wire harness (coloured black) that connects to the taillight by squeezing on the sides and pulling out.
Step 6:
Rotate the light bulb socket (yellow) counterclockwise and carefully pull it out to remove the bulb.
Replace the light bulb
Step 7:
Insert the wiring harness back into its socket.
Step 8:
Insert the bulb housing back into the taillight housing.
Lock the bulb housing in place by turning the bulb clockwise (about 1/4 to 1/2 turn).
Step 9:
Re-insert the taillight by sliding the light gently into the slot.
Press firmly to ensure the taillight is in place and the screw holes line up.
Step 10:
Use the Phillips #2 screwdriver to re-attach the two 8 mm screws back into the back of the taillight.
Step 11:
Reinstall the plastic trunk trim panel by lining the two clips up, and pressing down to snap them back into place.
Re-attach the rubber lining behind the plastic trim by pressing the rubber firmly to fit.
Step 12:
Close the trunk and test the light to make sure it works.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $21-$45)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($35-$75)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your 2020 Honda Accord instead of replacing it, you're preventing approximately 5799 kg of CO₂ emissions. Manufacturing a new 2020 Honda Accord generates 5800 kg of CO₂, while this repair only produces about 1 kg of CO₂. That's a 100% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your 2020 Honda Accord and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.