2020 Chevrolet Silverado Oil Change
Complete guide to 2020 Chevrolet Silverado oil change. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Oil Change is one of the most common repairs for 2020 Chevrolet Silverado. This repair involves replacing the damaged maintenance component with a new or refurbished part. The process typically takes 30-45 min and requires easy skill level.
What You'll Need
- Replacement maintenance part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Open the Hood
Make sure the engine is completely turned off and the key is out of the ignition before beginning.
The hood release handle is located on the driver's side to the left of the emergency brake pedal.
Pull on the hood release handle to pop the hood.
To open the hood, reach into the gap at the front of the truck and feel for the latch in the middle. Push it to the left to release it and lift up on the hood.
Step 2: Locate the Battery Compartment
The battery is located in the back left corner of the engine bay, partially covered by an engine bay brace.
Step 3: Remove the Engine Bay Brace
Remove the four bolts holding the engine bay brace to the body of the truck with a 13 mm socket and socket wrench. Remove the brace and set it to the side.
Step 4: Remove the Battery Hold Down
Locate the battery hold down, which is a small block held down on the right side of the battery compartment.
Use at least a 6-inch socket wrench extension to reach the 13 mm bolt and loosen it up.
Once it's completely loosened, reach down and pull out the bolt and the battery hold down block.
Step 5: Remove the Cables from the Battery Terminals
Locate the red positive cable and the black negative cable, both of which need to be removed using a 10 mm socket.
Remove the black negative cable first (and reinstall it last), which will prevent the possibility of shorting the battery to ground.
Step 6:
Loosen the 10 mm bolt on the black negative terminal just enough so you can lift it up and remove the cable.
Push the cable back and out of the way. A simple trick is to rest it on one of the engine bay braces to keep it from springing back.
Step 7:
Flip up the terminal cover on the red positive terminal and loosen the 10 mm bolt.
Lift up on the cable and move it out of the way. Resting it on the coolant reservoir keeps it from springing back.
Step 8: Remove the Battery
The battery may have carrying handles that you can flip up if they're not already.
Grab onto the handles with both hands and slowly lift the battery out of the battery compartment.
Batteries are very heavy (around 40 lbs.), so make sure you're able to safely lift the weight.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $21-$45)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($35-$75)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your 2020 Chevrolet Silverado instead of replacing it, you're preventing approximately 6098 kg of CO₂ emissions. Manufacturing a new 2020 Chevrolet Silverado generates 6100 kg of CO₂, while this repair only produces about 2 kg of CO₂. That's a 100% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your 2020 Chevrolet Silverado and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.