Skip to main content
🔧
HowMuchToFixAI for a Greener Future
Electrical
easy

2019 Ford Ranger Battery Replacement (Car)

Complete guide to 2019 Ford Ranger battery replacement (car). Cost estimates, difficulty level, time required, and environmental impact.

💰 Cost:$100 - $200
⏱️ Time:30 min
🌍 CO₂ Saved:6185 kg

🌍 Share Your Environmental Impact

Inspire others to repair instead of replace! Share how much CO₂ you're saving.

Share your impact:

💰 Cost Breakdown

Parts$60 - $120
Labor$40 - $80
Total Estimated Cost$100 - $200

💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.

🔧 Repair Overview

Battery Replacement (Car) is one of the most common repairs for 2019 Ford Ranger. This repair involves replacing the damaged electrical component with a new or refurbished part. The process typically takes 30 min and requires easy skill level.

🔧 Required Tools

What You'll Need

  • Replacement electrical part (OEM or aftermarket)
  • Precision screwdriver set (Phillips #000 or pentalobe)
  • Opening tools (plastic spudger, suction cup)
  • Adhesive strips or glue
  • Clean workspace with good lighting

Step-by-Step Process

Step 1:

Step 1 - Image 1
Step 1 - Image 2

Start the vehicle.

Turn the headlight dial to the "O" symbol to turn off the headlights.

Turn off vehicle.

Remove keys.

Step 2:

Step 2 - Image 1
Step 2 - Image 2

Pull the hood release to pop the vehicle's hood.

The hood release locates near the bottom of the driver side console below the headlight dial.

Push left and hold the yellow tab located under the middle of the hood.

Pull up on the hood.

Secure the hood open.

Step 3:

Step 3 - Image 1
Step 3 - Image 2

Pry the 5 plastic fasteners out with a flathead or a spudger.

Remove the two screws anchoring the air intake vent with a flathead screw driver.

Lift the intake vent to make room to slide the cover out.

Step 4:

Step 4 - Image 1
Step 4 - Image 2

Pry up along the edge of the cover with a flathead or a spudger to unclip it.

Listen for loud clicks as you pry up the edge. This indicates the clips are released.

Pull the cover off.

Set the cover aside.

The third photo is an example of vehicle with the cover removed.

Step 5:

Step 5 - Image 1
Step 5 - Image 2

Remove the 10mm bolts that anchor the grill to the frame with a socket wrench.

Use the socket wrench with the 10mm hex attachment

Step 6:

Step 6 - Image 1
Step 6 - Image 2

Using the T-25 Torx bit, unscrew the secondary cover from the frame.

There are 4 total screws on each of the corners of the cover.

Step 7:

Step 7 - Image 1
Step 7 - Image 2

Remove the secondary cover by shift and pulling it up with you hands.

The cover is not very flexible; remove slowly to reduce risk of breaking it.

Step 8:

Step 8 - Image 1
Step 8 - Image 2

Push down on the plastic clips to release them.

Push outwards on the outer clips to release them.

Pull the grill directly towards you once the all clips are released.

These clips are plastic and brittle. Be patient to make sure they do not break.

Removing the grill will take considerably longer than other steps since clips on one side have a tendency to snap back in once you move to the other.

Step 9:

Step 9 - Image 1
Step 9 - Image 2

Remove hardware that is anchoring down the head light using 10 mm hex bit.

Remove hardware that is anchoring down the head light using Philips head 2 screwdriver.

Step 10:

Step 10 - Image 1
Step 10 - Image 2

Remove wheel well lining to expose space under headlight.

Pry out side hazard light using a flat head screwdriver or spudger.

Remove T-25 torx screw.

Step 11:

Step 11 - Image 1

Pull away the fender guard to expose the last bolt the anchors the headlight to the body.

Pulling back the fender guard will require the release of a clip the was underneath the wheel-well liner.

Remove bolt using the 7mm hex bit.

Step 12:

Step 12 - Image 1
Step 12 - Image 2

Pull out the headlight.

Unplug the headlight cable.

📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.

iFixit Difficulty: Moderate | Time: NaNh NaNm

DIY vs Professional Repair

✋ DIY Repair

  • ✅ Lower cost (parts only: $60-$120)
  • ✅ Learn new skills
  • ❌ Risk of further damage
  • ❌ No warranty
  • ❌ Requires tools and time

🔧 Professional Repair

  • ✅ Expert installation
  • ✅ Warranty included
  • ✅ Faster turnaround
  • ❌ Higher cost ($100-$200)
  • ❌ Need to find reputable shop

Environmental Impact

By choosing to repair your 2019 Ford Ranger instead of replacing it, you're preventing approximately 6185 kg of CO₂ emissions. Manufacturing a new 2019 Ford Ranger generates 6200 kg of CO₂, while this repair only produces about 15 kg of CO₂. That's a 100% reduction in carbon emissions!

Get a Personalized Repair Estimate

Upload a photo of your 2019 Ford Ranger and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.

Related Repair Guides