2016 Audi A3 Headlight Bulb Replacement
Complete guide to 2016 Audi A3 headlight bulb replacement. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Headlight Bulb Replacement is one of the most common repairs for 2016 Audi A3. This repair involves replacing the damaged lighting component with a new or refurbished part. The process typically takes 15-30 min and requires easy skill level.
What You'll Need
- Replacement lighting part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Disconnect connectors and cable
Assuming you have viewed existing videos to remove the display housing, https://www.youtube.com/watch?v=O_eC99HVtEU
Ensure you have removed the display assembly with the ***screen in the down position.*** You ***MAY*** need to reconnect the assembly power briefly to move the screen to "up" position later on to remove the screen. The part we are replacing is the 5.8in LCD panel, part number C058GVC01.0
You will need to disconnect the 3 connectors ( marked RED) and cable removing 2 clips (marked GREEN) with flat blade screwdriver and a 3rd push-in clip (marked GREEN).
Step 2: Removing screws and shielding
Remove 5 screws from metal shielding. 2 each side and 1 in centre ( marked RED). Remove 2 screws from base of LCD panel tray (marked green) . Remove the metal shield and the plastic LCD panel tray.
Step 3: Remove ribbon cable and PCB
If the screen is not easily accessible to remove in next step, then you can change the position by: 1) Briefly replace the metal shield and reconnect the power connector to pop-up the screen. 2)Disconnect the power with the*** screen in the up position. ***
Remove the metal shield agan and now remove the ribbon cable and screen power connector. The ribbon cable connector has a black bar which should be lifted 90 degrees with a plastic spudger to permit removal.
Step 4: Screen removal
Lift the black plastic border pieces to unclip and pull away. They are also stuck with double-sided sticky tape which can just be pulled to remove. Remove the 2 small screws on each side of the screen. ***Keep the black borders safe for installing the new screen***
Use a plastic removal tool to pry the screen away from the frame, there is more double-sided tape securing the top part of the screen.
Keep the black border pieces and silver back plates, they are marked L and R for re-installing.
Clean and replace double-sided sticky tape with 3m automotive tape and replace screen, making sure to route cables to the bottom
Step 5: Screen replacement
Replace screen, folding over the ribbon cable and taping similar to the original. You can tape the power cable to ensure it stays at the bottom of the screen for re-installation. You cannot use a 7in screen to replace a 5.8in, NOR vice versa. Only use same part.
The original screen has a long plastic "L" along the bottom edge of the screen, secured with more double-sided sticky tape on the back ( marked in RED). This can be removed by taking a sharp hobby knife and cutting along the tape to remove it. Apply new 3m automotive tape to the back of the new screen and re-apply the "L" shaped plastic
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Moderate | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $12-$60)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($20-$100)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your 2016 Audi A3 instead of replacing it, you're preventing approximately 6399 kg of CO₂ emissions. Manufacturing a new 2016 Audi A3 generates 6400 kg of CO₂, while this repair only produces about 1 kg of CO₂. That's a 100% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your 2016 Audi A3 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.