2013 Toyota Highlander Tire Rotation
Complete guide to 2013 Toyota Highlander tire rotation. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Tire Rotation is one of the most common repairs for 2013 Toyota Highlander. This repair involves replacing the damaged tires component with a new or refurbished part. The process typically takes 30-45 min and requires easy skill level.
What You'll Need
- Replacement tires part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1:
If the sun visor is folded up, fold it down.
Step 2:
Unclip the sun visor from the inside hook on the ceiling of the passenger side.
Step 3:
Move the sun visor to the side in order to allow for easier access to the plastic cover.
If you are replacing the ***driver side*** sun visor, move the sun visor to your left; if you are replacing the ***passenger side*** sun visor, move the sun visor to your right.
Step 4:
Use a trim removal tool or a plastic opening tool to gently pry the plastic cover from the base of the visor.
Step 5:
Remove the plastic cover by pulling it back and wiggling it free from the sun visor.
Don't be afraid to use a little force—the cover is made out of a soft plastic, so it won't break easily.
Step 6:
Use a Phillips #2 screwdriver to remove the bottom 2.5 mm screw from the plastic base of the sun visor.
Step 7:
Use the Phillips #2 screwdriver to remove the top 2.5 mm screw.
Support the sun visor with your free hand while removing the second screw to prevent it from falling.
Step 8:
Lightly pull down on the plastic base to unplug the sun visor.
Depending on the make of the sun visor, you may need to also press on a tab located underneath the plastic base.
Set the visor aside.
Step 9:
Press down on the front clip to release the visor bracket cover from the mounting bracket.
Step 10:
Slide the C-shaped cover off the bracket through the open end.
You may need to pull it if it doesn't slide off easily.
Step 11:
Lift the replacement visor to the socket on the sealing, ensuring the plastic base and screw holes are aligned.
Step 12:
Push the sun visor connector into the socket until it sits flush with the ceiling.
Use a Phillips #2 screwdriver to tighten the screws and secure the sun visor connector.
Remember to slide the C-shaped bracket cover over the top of the connector.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $21-$45)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($35-$75)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your 2013 Toyota Highlander instead of replacing it, you're preventing approximately 5999 kg of CO₂ emissions. Manufacturing a new 2013 Toyota Highlander generates 6000 kg of CO₂, while this repair only produces about 1 kg of CO₂. That's a 100% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your 2013 Toyota Highlander and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.