2012 Audi Q7 Oil Change
Complete guide to 2012 Audi Q7 oil change. Cost estimates, difficulty level, time required, and environmental impact.
🌍 Share Your Environmental Impact
Inspire others to repair instead of replace! Share how much CO₂ you're saving.
💰 Cost Breakdown
💡 Tip: Costs vary by location and repair shop. Authorized service centers typically charge more than independent repair shops.
🔧 Repair Overview
Oil Change is one of the most common repairs for 2012 Audi Q7. This repair involves replacing the damaged maintenance component with a new or refurbished part. The process typically takes 30-45 min and requires easy skill level.
What You'll Need
- Replacement maintenance part (OEM or aftermarket)
- Precision screwdriver set (Phillips #000 or pentalobe)
- Opening tools (plastic spudger, suction cup)
- Adhesive strips or glue
- Clean workspace with good lighting
Step-by-Step Process
Step 1: Verify your driveshaft part number
Verify your driveshaft part number
It takes two seconds to get under the car and get the part number off the driveshaft. You won't even need to remove any shielding covers!
*for vehicles equipped with air suspension, make it easy on yourself by putting the car in "off-road" or "lift" mode before climbing under the passenger side for the easiest access.
Step 2: Order the appropriate kit and check the box
Check and verify the kit along with making sure everything is included. We are all human, so mistakes are made sometimes.
*this kit included both "street" & "track" bushings. Your kit may differ due to parts included in the application ordered.
Step 3:
Lift or ground, SAFETY FIRST! Use some blocks to eliminate any possible chance of the car rolling away. I've seen it happen when people are doing any driveshaft work.
Step 4: Prepare yourself to cut the center bearing support housing
Just be mentally ready if you aren't the type that modifies your vehicle. Its an easy job, but some people freak out when they break out a tool and start cutting away.
Take note of any wiring or tubing and either move out of the way or make sure to steer clear. There shouldn't be anything other than one harness near the area.
Notice the slop and look at just how much driveshaft flex is in the OEM unit. The replacement is much sturdier and there will be minimal play in the new bushing.
Step 5:
Cut the mount in a way that will allow you to spin the bearing carrier to the opposite side and access the thinner metal of the bracket.
*Video to show explanation in next step.
Step 6:
Rotate the bearing to the opposite side to access area to cut in order to fully remove the OEM bearing carrier.
Step 7:
Once rotated and cut, you may need a screwdriver to spread the carrier enough to remove from the driveshaft assembly.
You will also need to cut through the additional metal surround that encompasses the stock rubber dampener.
Slice around the rubber to make it easy when spreading this portion to remove from the driveshaft assembly.
Step 8:
Trim the rubber off of the smaller portion in the middle, but leave the smallest portion that surrounds the actual bearing.
*including a picture of the disassembled OEM carrier for reference.
Step 9:
Get out the M10 Triple Square bit and remove the stock driveshaft carrier bolts.
Step 10:
Your 5mm allen socket will be used to dissassemble the new JXB carrier assembly for the install.
Split the housing and familiarize yourself with how the new carrier is assembled.
Step 11:
Make sure everything is lined up correctly and tighten the JXB Performance carrier onto the driveshaft center bearing.
Lettering on the JXB unit will face toward the FRONT of the vehicle.
*torque on the allen bolts is 25nm
Check to ensure even fitment and the new driveshaft carrier bolts line up with the stock mounting location.
Step 12:
Assemble the mounting hardware and bolt the carrier back into proper placement reverse of how you removed.
Torque bolts to 19nm and use some threadlock blue on these.
Step 13:
Take the car for a brief test drive to make sure everything was done correctly!
You should have many years of use left in this quality replacement with an easy to replace solution if needed down the road.
📖 Repair guide provided by iFixit - The free repair manual. Licensed under CC BY-NC-SA 3.0.
iFixit Difficulty: Easy | Time: NaNh NaNm
DIY vs Professional Repair
✋ DIY Repair
- ✅ Lower cost (parts only: $21-$45)
- ✅ Learn new skills
- ❌ Risk of further damage
- ❌ No warranty
- ❌ Requires tools and time
🔧 Professional Repair
- ✅ Expert installation
- ✅ Warranty included
- ✅ Faster turnaround
- ❌ Higher cost ($35-$75)
- ❌ Need to find reputable shop
Environmental Impact
By choosing to repair your 2012 Audi Q7 instead of replacing it, you're preventing approximately 6398 kg of CO₂ emissions. Manufacturing a new 2012 Audi Q7 generates 6400 kg of CO₂, while this repair only produces about 2 kg of CO₂. That's a 100% reduction in carbon emissions!
Get a Personalized Repair Estimate
Upload a photo of your 2012 Audi Q7 and get an AI-powered cost estimate in seconds. See exactly what's damaged and how much it'll cost to fix.